| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADPL74101 bảng dữ liệu(PDF) 23 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADPL74101 bảng dữ liệu(HTML) 23 Page - Analog Devices |
|
23 / 49 page ![]() Data Sheet ADPL74101 analog.com Rev. 0 23 of 49 APPLICATIONS INFORMATION Use Cases Figure 1 is a simplified ADPL74101 application circuit. External component selection is largely driven by the load requirements and begins with selecting the inductor, current-sense components, operating frequency, and light- load operating mode. The remaining power stage components, consisting of the input and output capacitors and power FETs, can then be chosen. Next, feedback resistors are selected to set the desired output voltage. Then, the remaining external components are selected, inluding soft start, biasing, and loop compensation. Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. A higher frequency generally results in lower efficiency because of FET switching and gate charge losses. In addition to this trade-off, the effect of the inductor value on ripple current and low-current operation must also be considered. The inductor value directly affects the ripple current. The maximum average inductor current (IL(MAX)) is equal to the maximum output current. The peak current is equal to the average inductor current plus half of the inductor ripple current (ΔIL), which decreases with higher inductance (L) or higher frequency (f) and increases with higher VIN, as shown in Equation 1: ∆IL = 1 f × L VOUT (1 − VOUT VIN ) (1) Accepting larger values of ΔIL allows the use of low inductances, but results in higher output-voltage ripple and greater core losses. A reasonable starting point for setting ripple current is ΔIL = 0.3 × IL(MAX). The maximum ΔIL occurs at the maximum input voltage. The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below 25% of the current limit determined by RSENSE. Lower inductor values (higher ΔIL) cause this transition to occur at lower load currents, which can cause a dip in efficiency in the upper range of low-current operation. In Burst Mode operation, lower inductance values cause the burst frequency to decrease. Inductor Core Selection When the value for higher inductance (L) is known, select the type of inductor. High-efficiency regulators generally cannot afford the core loss found in low-cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is dependent on the inductance value selected. As inductance increases, core losses decrease. However, because increased inductance requires more turns of wire, copper losses increase. Ferrite designs have low core loss and are preferred for high switching frequencies. Therefore, design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates hard, meaning inductance collapses abruptly when the peak design current is exceeded. This collapse results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |