| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADPL74101 bảng dữ liệu(PDF) 34 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADPL74101 bảng dữ liệu(HTML) 34 Page - Analog Devices |
|
34 / 49 page ![]() Data Sheet ADPL74101 analog.com Rev. 0 34 of 49 Figure 40. Relationship Between INTVCC Voltage and Resistor Value at the DRVSET Pin High-input-voltage applications in which large FETs are driven at high frequencies can exceed the maximum junction temperature rating for the ADPL74101. The INTVCC current, which is dominated by the gate charge current, can be supplied by either the VIN LDO regulator or the EXTVCC LDO regulator. When the voltage on the EXTVCC pin is less than its switchover threshold (4.76V or 5.95V, as determined by the DRVUV pin), the VIN LDO regulator is enabled. In this case, power dissipation for the IC is equal to VIN× INTVCC current (IINTVCC). The gate charge current is dependent on the operating frequency, as discussed in the Efficiency Considerations section. To estimate the junction temperature, use the equation detailed in Table 2. For example, the ADPL74101 INTVCC current is limited to less than 36mA from a 36V supply when not using the EXTVCC supply at an ambient temperature of 70°C, as shown in Equation 20: TJ = 70°C + (36mA)(36V)(43°C/W) = 125°C (20) To prevent the maximum junction temperature from exceeding, check the input supply current while operating in continuous conduction mode (MODE = INTVCC) at maximum VIN. When the voltage applied to EXTVCC exceeds its rising switchover threshold, the VIN LDO regulator turns off, and the EXTVCCLDO regulator enables. The EXTVCC LDO regulator remains on as long as the voltage applied to EXTVCC remains above its falling switchover threshold. The EXTVCC LDO regulator attempts to regulate the INTVCC voltage to the voltage as programmed by the DRVSET pin. Therefore, while EXTVCC is less than 5V, the LDO regulator is in dropout, and the INTVCC voltage is approximately equal to EXTVCC. When EXTVCC exceeds the programmed voltage (up to an absolute maximum of 30V), INTVCC is regulated to the programmed voltage. Using the EXTVCC LDO regulator allows the FET driver and control power to be derived from the switching regulator output of the ADPL74101 (4.7V ≤ VOUT ≤ 30V) during normal operation, and from the VIN LDO regulator when the output is out of regulation (for example, during startup or short-circuit). If more current is required through the EXTVCC LDO regulator than is specified, add an external Schottky diode between the EXTVCCand INTVCC pins. In this case, do not apply more than 6V to the EXTVCC pin. Significant efficiency and thermal gains can be realized by powering INTVCC from an output, because the VIN current resulting from the driver and control currents is scaled by a factor of VOUT/(VIN × efficiency). For 5V to 30V regulator outputs, connect the EXTVCC pin to VOUT. Tying the EXTVCC pin to an 8.5V supply reduces the junction temperature as shown in Equation 20 from 125°C to the results given by Equation 21, as follows: TJ= 70°C + (36mA)(8.5V)(43°C/W) = 83°C (21) DRVSET PIN RESISTOR (kΩ) 50 5.5 5.4 5.3 5.2 5.1 5.0 4.6 4.4 4.2 4.7 4.8 4.9 4.5 4.3 4.1 4.0 80 110 70 90 120 100 60 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |