| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADPL74101 bảng dữ liệu(PDF) 41 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADPL74101 bảng dữ liệu(HTML) 41 Page - Analog Devices |
|
41 / 49 page ![]() Data Sheet ADPL74101 analog.com Rev. 0 41 of 49 5. Connect the INTVCC decoupling capacitor close to the IC, between the INTVCC and the power GND pin. This capacitor carries the current peaks of the FET drivers. Place an additional 1μF ceramic capacitor between the DRVCC and GND pins to improve noise performance. 6. Keep the switching node (SW), top gate nodes (TG), and boost node (BOOST) away from sensitive small signal nodes, especially from the voltage and current sensing feedback pins. All of these nodes exhibit large, and fast-moving signals. Therefore, keep the nodes on the output side of the ADPL74101 and ensure they occupy the minimum PCB trace area. 7. Use a modified star ground technique: a low-impedance, large-copper-area central grounding point on the same side of the PCB as the input and output capacitors, with tie-ins to the bottom of the INTVCC decoupling capacitor, the bottom of the voltage feedback resistive divider, and the GND pin of the IC. Figure 41. Branch Current Waveforms PCB Layout Debugging Use a DC to 50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (the SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation is maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold, typically 25% of the maximum designed current level in Burst Mode operation. The duty cycle percentage is maintained from cycle to cycle in a well-designed, low-noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage-sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame an improper PCB layout if regulator bandwidth optimization is not required. Reduce the VIN from its nominal level to verify the operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, check for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. Place the capacitor across the current-sensing pins next to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high-frequency capacitive coupling. If problems are encountered with high-current output loading at lower input voltages, look for inductive coupling between CIN, the top FET, and the bottom FET components to the sensitive current and voltage RL1 L1 SW RSENSE VOUT COUT VIN CIN RIN BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |