| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AD4062 bảng dữ liệu(PDF) 40 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD4062 bảng dữ liệu(HTML) 40 Page - Analog Devices |
|
40 / 71 page ![]() Data Sheet AD4062 SERIAL INTERFACE analog.com Rev. 0 | 40 of 71 CONV_READ REGISTER The CONV_READ register can be used to trigger continuous ADC conversions in a loop where reading the conversion results of one ADC conversion initiates the next ADC conversion. To trigger ADC conversions using the CONV_READ register, up- date the ADDR_PTR to point to any of the register addresses of the CONV_READ register (from 0x50 to 0x53). Then, perform a dummy I3C read from the AD4062 and issue a repeated start (Sr) followed by a stop (P) at the end of the data phase. The SDA rising edge of the stop (P) triggers an ADC convert-start as shown in Figure 66. In sample mode, the convert-start trigger results in a single conversion. In burst averaging mode, the convert-start trigger results in a burst of multiple conversions which are used to generate a single averaged result (see the Modes of Operation section). When the next I3C read is performed, the data bits read from the target will be the ADC conversion results stored in CONV_READ. The repeated start (Sr) followed by a stop (P) of this read will trigger the next ADC conversion, and therefore the host can repeatedly read from CONV_READ to continuously generate and read back ADC samples. Note that before reading conversion results from CONV_READ, it is important to ensure that the correct number of data bytes will be read from the AD4062 depending on the operating mode. Table 22 shows the contents of the CONV_READ register for sample mode, trigger mode, and burst averaging mode. Table 17 shows the recommended ADDR_PTR setting for reading out data in each mode to minimize the number of bytes to be read per conversion. Figure 66. Triggering ADC Conversions Using CONV_READ Table 22. CONV_READ Register Contents ADC Mode Byte 0x53 (CONV_READ [31:24]) Byte 0x52 (CONV_READ [23:16]) Byte 0x51 (CONV_READ [15:8]) Byte 0x50 (CONV_READ [7:0]) Sample Mode and Trigger Mode SE[15:8]1 SE[7:0] DATA[15:8] DATA[7:0] Burst Averaging Mode SE[11:4] SE[3:0], DATA[19:16] DATA[15:8] DATA[7:0] 1 SE refers to the Sign Extension bits. When the ADC is in differential mode, the value of the SE bits is the same as the most significant data bit. When the ADC is in single-ended mode, the SE bits are always = 0. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |