L99PM72GXP datasheet(19/129 Pages) STMICROELECTRONICS

19 / 129 page

DocID024767 Rev 4

19/129

L99PM72GXP

Detailed description

128

A cyclic supply of external contacts and a synchronized monitoring of the contact state can

be activated and configured by SPI.

In V1_standby mode various wake-up sources can be individually programmed. Each wake-

up event puts the device into Active Mode and forces the RxDL/NINT pin to a low level

indicating the wake-up condition to the microcontroller.

After Power ON Reset (POR) all wake up sources are activated by default except the

periodic interrupt / wake timer.

With the interrupt timer the micro controller can be forced from 'stop' to 'run' after a

programmable period. The RxDL/NINT pin is forced low after the timer is elapsed. The

L99PM72GXP enters active mode and is awaiting a valid watchdog trigger.

Both internal timers can be used for this feature.

The interrupt timer (TINT) at pin RxDL/NINT is only available in V1_standby mode.

Note:

Inputs TxDL, TxDC must be at recessive (high) level and CSN must be at high level or at

high impedance in order to achieve minimum standby current in V1_standby Mode.

Inputs DI and CLK must be at GND or at high impedance to achieve minimum standby

current in V1_standby Mode.

2.2.5

Interrupt

The interrupt signal (linked to RxDL/NINT) indicates a wake-up event from V1_standby mode.

In case of a wake-up by Wake-up Inputs, activity on LIN or CAN, SPI access or Timer-

Interrupt the RxDL/NINT pin is pulled low for t = tinterrupt.

If the CAN transceiver is deactivated during Active Mode (CAN_ACT = 0), a WUP

(SWEN = 0) or a WUF (SWEN = 1) generates an interrupt at RxDC/NINT to signalize CAN

communication on the bus to the microcontroller.

In case of a CAN communication timeout an interrupt at RxDC /NINT is generated and the

CAN_TO flag is set.

In case of V1_standby mode and (IV1 >ICMP), the device remains in standby mode, the V1

regulator switches to high current mode and the watchdog starts. No Interrupt signal is

generated.

Table 3. CAN wake-up signalization

Operating

mode

Event

Wake-up

transition to

active

Status flag

Interrupt

Transceiver

state

Active

WUP or WUF(1)

Not applicable

Wake_CAN WUP

WUP/WUF

RxDC

TRX_STBY

CAN timeout

CAN_TO

RxDC

TRX_STBY

V1_standby

WUP or WUF(1)

Yes

Wake_CAN WUP

WUP/WUF

RxDL

TRX_STBY

CAN timeout

CAN_TO

RxDC

TRX_STBY

L99PM72GXP bảng dữ liệu(PDF) 19 Page - STMicroelectronics

L99PM72GXP bảng dữ liệu(HTML) 19 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL