L9300 datasheet(164/178 Pages) STMICROELECTRONICS

164 / 178 page

1. Dimensioning and tolerancing schemes conform to ASME Y14.5M-1994.

2. The top package body size may be smaller than the bottom package size by as much as to 0.15 mm.

3. Datum A-B and D to be determined at datum plane H.

4. To be determined at seating datum plane C.

5. Dimensions D1 and E1 do not include mold flash or protrusions. Allowable mold flash or protrusions is “0.25

mm” per side. D1 and E1 are maximum plastic body size dimensions including mold mismatch.

6. Details of pin 1 identifier are optional but must be located within the zone indicated.

7. All dimensions are in millimeters.

8. No intrusion allowed inwards the leads.

9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall not cause the lead width

to exceed the maximum “b” dimension by more than 0.08 mm. Dambar cannot be located on the lower radius

or the foot. Minimum space between protrusion and an adjacent lead is 0.07 mm for 0.4 mm and 0.5 mm pitch

packages.

10. Exact shape of each corner is optional.

11. These dimensions apply to the flat section of the lead between 0.10 mm and 0.25 mm from the lead tip.

12. A1 is defined as the distance from the seating plane to the lowest point on the package body.

13. Dimensions D2 and E2 show the maximum exposed metal area on the package surface where the exposed

pad is located (if present). It includes all metal protrusions from exposed pad itself.

14. Dimensions D3 and E3 show the minimum solderable area, defined as the portion of exposed pad which is

guaranteed to be free from resin flashes/bleeds, bordered by internal edge of inner groove.

15. The optional exposed pad is generally coincident with the top or bottom side of the package and not allowed

to protrude beyond that surface.

16. “N” is the number of terminal positions for the specified body size.

20.2

TQFP80 (14x14x1 mm. exp. pad up) marking information

Figure 73. TQFP80 (14x14x1 mm. exp. pad up) marking information

Pin1 Ref.

Marking area

Special function digit

ES: Engineering sample

&: Engineering sample

<blank>: Commercial sample

GADG2906171523PS

Parts marked as ‘ES’ or ‘&’ are not yet qualified and therefore not approved for use in production. ST is not

responsible for any consequences resulting from such use. In no event will ST be liable for the customer using

any of these engineering samples in production.

ST’s Quality department must be contacted prior to any decision to use these engineering samples to run a

qualification activity.

L9300

Package information

DS12258 - Rev 5

page 164/178

L9300 bảng dữ liệu(PDF) 164 Page - STMicroelectronics

L9300 bảng dữ liệu(HTML) 164 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL