| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
RF430CL331HIPW bảng dữ liệu(PDF) 23 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
RF430CL331HIPW bảng dữ liệu(HTML) 23 Page - Texas Instruments |
|
23 / 63 page ![]() Reader (PCD) RF430CL331H (PICC) Host Controller ReadBinary command is sent Is the data already available? RF Responds with the data over the serial bus No/Interrupt INTO Sends the data using ISO14443-B protocol I 2 C Yes PCD processes the data and possibly repeats the cycle RF If necessary RF430CL331H www.ti.com SLASE18A – SEPTEMBER 2015 – REVISED NOVEMBER 2015 Response register (see Section 5.11.8). Servicing of the Select command is complete. 4. RF430CL331H procedure: (a) If the custom Status Words (SW) feature was not used: (i) If the host controller indicated that the file existed, the response to the PCD is SW1 = 90h and SW2 = 00h. (ii) If the host controller indicated that the file did not exist, the response to the PCD is SW1 = 6Ah and SW2 = 82h. (b) If the custom response feature was used, the response to the PCD is what was set in the Custom Status Word Response register (see Section 5.11.13). 5.9.2 NDEF or Capability Container Read Binary Procedure This read procedure does not change between when the PCD reads the Capability Container or an NDEF file. These two types of reads can be differentiated by the file identifier that the RF430CL331H reports in the NDEF File Identifier register (see Section 5.11.7). For the general flow, see Figure 5-8. Figure 5-8. Read System Flow The procedure: 1. PCD procedure: (a) Issues a Capability Container or a NDEF Read Binary command. 2. RF430CL331H procedure: (a) Receives the RF packet. (b) Checks its buffer and determines if all of the requested data in the Read Binary command exists already in the buffer. (c) If all the data is available in the buffer then (in the case that extra data was written in a previous read request): (i) No interrupt is issued to the host controller. (ii) The data is supplied in the response packet to the PCD automatically. (iii) The status word response SW1 = 90h and SW2 = 00h is appended to the packet. (iv) The flow returns to wait for the next Type 4 request. (d) If no data or only partial data is available, then an interrupt is issued to the host controller. 3. Host controller procedure: (a) An interrupt is received. (b) Checks the source of the interrupt by reading the interrupt registers (see Section 5.11.3). Copyright © 2015, Texas Instruments Incorporated Detailed Description 23 Submit Documentation Feedback Product Folder Links: RF430CL331H |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |