ADIN1300CCPZ-R7 datasheet(65/96 Pages) AD

65 / 96 page

Data Sheet

ADIN1300

analog.com

Rev. B | 65 of 96

Table 57. Bit Descriptions for LED_CTRL_1 (Continued)

Bits

Bit Name

Description

Reset

Access

LED_PUL_STR_EN

Setting this bit enables pulse stretching for transmit, receive, or collision LED events so that very short

duration events are visible. The LED pulse stretching enable register indicates that the PHY must

stretch any pulses indicating transmit, receive, or collision. Without stretching, these pulses may be

too short to cause an LED to light.

0x1

R/W

LED Control 2 Register

Address: 0x001C, Reset: 0x210A, Name: LED_CTRL_2

This register provides access to various PHY LED control register bits.

Table 58. Bit Descriptions for LED_CTRL_2

Bits

Bit Name

Description

Reset

Access

[15:4]

RESERVED

Reserved.

0x210

R/W

[3:0]

LED_A_CFG

LED_0 configuration is made up of five bits. These four bits, Bits[3:0], are the LSBs and Bit 4 is from

LED_A_EXT_CFG_EN (LED_CTRL_1 register, Address 0x001B). The combination of the five bits configures LED_0,

selecting one of 32 possible configuration functions according to the following settings. The default setting is 01010 (on

if link up and blink on activity).

0xA

R/W

11111: on if 10BASE-T link, blink if 100BASE-TX link.

11110: on if 10BASE-T link, blink if 1000BASE-T link.

11101: on if 100BASE-TX link, blink if 10BASE-T link.

11100: on if 100BASE-TX link, blink if 1000BASE-T link.

11011: on if 1000BASE-T link, blink if 10BASE-T link.

11010: blink if transmit.

11001: blink on activity.

11000: on if 10BASE-T or 1000BASE-T link, blink on activity.

10111: on if 10BASE-T or 1000BASE-T link.

10110: on if 100BASE-TX or 1000BASE-T link, blink on activity.

10101: on if 10BASE-T or 100BASE-TX link, blink on activity.

10100: on if 1000BASE-T link, blink on activity.

10011: on if 100BASE-TX link, blink on activity.

10010: on if 10BASE-T link, blink on activity.

10001: on if 100BASE-TX or 1000BASE-T link.

10000: on if 10BASE-T or 100BASE-TX link.

01111: off.

01110: on.

01101: blink.

01100: on if full duplex link, blink on collision.

01011: on if link, blink if receiving.

01010: on if link, blink on activity (default).

01001: on if collision.

01000: on if full duplex link.

00111: on if activity (transmitting or receiving).

00110: on if receiving.

00101: on if transmitting.

00100: on if link up.

ADIN1300CCPZ-R7 bảng dữ liệu(PDF) 65 Page - Analog Devices

ADIN1300CCPZ-R7 bảng dữ liệu(HTML) 65 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

bảng dữ liệu tải về

Link URL