MPC5553_07 datasheet(5/66 Pages) FREESCALE

5 / 66 page

Electrical Characteristics

MPC5553 Microcontroller Data Sheet, Rev. 2.0

Freescale Semiconductor

VRH to VDDA differential voltage

VRH – VDDA

–5.5

5.5

VRL to VSSA differential voltage

VRL – VSSA

–0.3

0.3

VDDEH to VDDA differential voltage

VDDEH – VDDA

–VDDA

VDDEH

VDDF to VDD differential voltage

VDDF – VDD

–0.3

0.3

This spec has been moved to Table 9, spec 43a.

VSSSYN to VSS differential voltage

VSSSYN – VSS

–0.1

0.1

VRCVSS to VSS differential voltage

VRCVSS – VSS

–0.1

0.1

Maximum DC digital input current 9

(per pin, applies to all digital pins)

IMAXD

–2

Maximum DC analog input current 10

(per pin, applies to all analog pins)

IMAXA

–3

Maximum operating temperature range 11

Die junction temperature

150.0

Storage temperature range

TSTG

–55.0

150.0

Maximum solder temperature 12

TSDR

—

260.0

Moisture sensitivity level 13

MSL

—

1 Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only,

and functional operation at the maxima is not guaranteed. Stress beyond the listed maxima can affect device reliability or cause

permanent damage to the device.

2 Absolute maximum voltages are currently maximum burn-in voltages. Absolute maximum specifications for device stress have

not yet been determined.

3 1.5 V +/– 10% for proper operation. This parameter is specified at a maximum junction temperature of 150 oC.

4 All functional non-supply I/O pins are clamped to V

SS and VDDE, or VDDEH.

5 AC signal overshoot and undershoot of up to +/– 2.0 V of the input voltages is permitted for an accumulative duration of

60 hours over the complete lifetime of the device (injection current not limited for this duration).

6 Internal structures hold the voltage greater than –1.0 V if the injection current limit of 2 mA is met. Keep the negative DC

current greater than –0.6 V on eTPUB[15] and SINB during the internal power-on reset (POR) state.

7 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V

DDEH supplies, if the

maximum injection current specification is met (2 mA for all pins) and VDDEH is within the operating voltage specifications.

8 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V

DDE supplies, if the maximum

injection current specification is met (2 mA for all pins) and VDDE is within the operating voltage specifications.

9 Total injection current for all pins (including both digital and analog) must not exceed 25 mA.

10 Total injection current for all analog input pins must not exceed 15 mA.

11 Lifetime operation at these specification limits is not guaranteed.

12 Solder profile per CDF-AEC-Q100.

13 Moisture sensitivity per JEDEC test method A112.

Table 2. Absolute Maximum Ratings1 (continued)

Spec

Characteristic

Symbol

Min

Max2

Unit

MPC5553 bảng dữ liệu(PDF) 5 Page - Freescale Semiconductor, Inc

MPC5553 bảng dữ liệu(HTML) 5 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

bảng dữ liệu tải về

Link URL