AD9957SLASHPCBZ datasheet(53/60 Pages) AD

53 / 60 page

AD9957

Rev. 0 | Page 53 of 60

I/O Update Rate Register

Address 0x04, four bytes are assigned to this register. This register is effective without the need for an I/O update.

Table 22. Bit Descriptions for I/O Update Rate Register

Bit(s)

Mnemonic

Description

31:0

I/O Update Rate

Ineffective unless CFR2 Bit 23 = 1. This 32-bit number controls the automatic I/O update rate (see the

Automatic I/O Update section); default is 0xFFFFFFFF.

RAM Segment Register 0

Address 0x05, six bytes are assigned to this register. This register is effective without the need for an I/O update. This register is only

active if CFR1 Bit 31 = 1 and there is a Logic 0 to Logic 1 transition on the RT pin.

Table 23. Bit Descriptions for RAM Segment Register 0

Bit(s)

Mnemonic

Description

47:32

RAM Address Step

Rate 0

This 16-bit number controls the rate at which the RAM state machine steps through the specified RAM

address range.

31:22

RAM End Address 0

This 10-bit number identifies the ending address for the RAM state machine.

21:16

Not Available

15:6

RAM Start Address 0

This 10-bit number identifies the starting address for the RAM state machine.

5:3

Not Available

2:0

RAM Playback Mode 0

This 2-bit number identifies the playback mode for the RAM state machine (see Table 6).

RAM Segment Register 1

Address 0x06, six bytes are assigned to this register. This register is only active if CFR1 Bit 31 = 1 and there is a Logic 1 to Logic 0

transition on the RT pin.

Table 24. Bit Descriptions for RAM Segment Register 1

Bit(s)

Mnemonic

Description

47:32

RAM Address Step

Rate 1

This 16-bit number controls the rate at which the RAM state machine steps through the specified RAM

address range.

31:22

RAM End Address 1

This 10-bit number identifies the ending address for the RAM state machine.

21:16

Not Available

15:6

RAM Start Address 1

This 10-bit number identifies the starting address for the RAM state machine.

5:3

Not Available

2:0

RAM Playback Mode 1

This 2-bit number identifies the playback mode for the RAM state machine (see Table 6).

Amplitude Scale Factor Register (ASF)

Address 0x09, four bytes are assigned to this register. This register is only active if CFR1 Bit 9 = 1.

Table 25. Bit Descriptions for ASF Register

Bits

Mnemonic

Description

31:16

Amplitude Ramp Rate

Ineffective unless CFR1 Bit 8 = 1. This 16-bit number controls the rate at which the OSK controller

updates amplitude changes to the DDS.

If CFR1 Bit 8 = 0 and CFR1 Bit 23 = 0, then this 14-bit number is the amplitude scale factor for the DDS.

If CFR1 Bit 8 = 0 and CFR1 Bit 23 = 1, then this 14-bit number is the amplitude scale factor for the DDS

when the OSK pin is Logic 1.

15:2

Amplitude Scale Factor

If CFR1 Bit 8 = 1, then this 14-bit number sets a ceiling on the maximum allowable amplitude scale

factor for the DDS.

1:0

Amplitude Step Size

Ineffective unless CFR1 Bit 8 = 1. This 2-bit number controls the step size for amplitude changes to the

DDS (see Table 10).

AD9957/PCBZ bảng dữ liệu(PDF) 53 Page - Analog Devices

AD9957/PCBZ bảng dữ liệu(HTML) 53 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

bảng dữ liệu tải về

Link URL