L160DB90VC datasheet(23/52 Pages) AMD

23 / 52 page

22358B7 May 5, 2006

Am29LV160D

DA TA

SH EET

Any commands written to the device during the Em-

bedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program-

ming oper ation . Th e B y te Progr a m command

sequence should be reinitiated once the device has

reset to reading array data, to ensure data integrity.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from a “0” back to a “1”. Attempting to do so may

halt the operation and set DQ5 to “1,” or cause the

Data# Polling algorithm to indicate the operation was

successful. However, a succeeding read will show that

the data is still “0”. Only erase operations can convert

a “0” to a “1”.

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to pro-

gram bytes or words to the device faster than using the

standard program command sequence. The unlock

bypass command sequence is initiated by first writing

two unlock cycles. This is followed by a third write

cycle containing the unlock bypass command, 20h.

The device then enters the unlock bypass mode. A

two-cycle unlock bypass program command sequence

is all that is required to program in this mode. The first

cycle in this sequence contains the unlock bypass pro-

gram command, A0h; the second cycle contains the

program address and data. Additional data is pro-

grammed in the same manner. This mode dispenses

with the initial two unlock cycles required in the stan-

dard program command sequence, resulting in faster

total programming time. Table 9 shows the require-

ments for the command sequence.

During the unlock bypass mode, only the Unlock By-

pass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset com-

mand sequence. The first cycle must contain the data

90h; the second cycle the data 00h. Addresses are

don’t care for both cycles. The device then returns to

reading array data.

Figure 3 illustrates the algorithm for the program oper-

ation. See the Erase/Program Operations table in “AC

Characteristics” for parameters, and to Figure 17 for

timing diagrams.

Note: See Table 9 for program command sequence.

Figure 3.

Program Operation

Chip Erase Command Sequence

Chip erase is a six bus cycle operation. The chip erase

command sequence is initiated by writing two unlock

cycles, followed by a set-up command. Two additional

unlock write cycles are then followed by the chip erase

command, which in turn invokes the Embedded Erase

algorithm. The device does not require the system to

preprogram prior to erase. The Embedded Erase algo-

rithm automatically preprograms and verifies the entire

memory for an all zero data pattern prior to electrical

erase. The system is not required to provide any con-

trols or timings during these operations. Table 9 shows

the address and data requirements for the chip erase

command sequence.

Any commands written to the chip during the Embed-

ded Erase algor ithm are ignored . Note that a

hardware reset during the chip erase operation im-

mediately terminates the operation. The Chip Erase

command sequence should be reinitiated once the de-

vice has returned to reading array data, to ensure data

integrity.

The system can determine the status of the erase op-

eration by using DQ7, DQ6, DQ2, or RY/BY#. See

“Write Operation Status” for information on these sta-

tus bits. When the Embedded Erase algorithm is

complete, the device returns to reading array data and

addresses are no longer latched.

START

Write Program

Command Sequence

Data Poll

from System

Verify Data?

Yes

Last Address?

Yes

Programming

Completed

Increment Address

Embedded

Program

algorithm

in progress

L160DB90VC bảng dữ liệu(PDF) 23 Page - Advanced Micro Devices

L160DB90VC bảng dữ liệu(HTML) 23 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

bảng dữ liệu tải về

Link URL