| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
NT5DS32M4AT bảng dữ liệu(PDF) 52 Page - Nanya Technology Corporation. |
|
|
|||||||||||||||||||||||||||||
NT5DS32M4AT bảng dữ liệu(HTML) 52 Page - Nanya Technology Corporation. |
|
52 / 76 page ![]() NT5DS32M4AT NT5DS16M8AT 128Mb Double Data Rate SDRAM REV 1.0 05/2001 52 © NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. Normal Strength Driver Pulldown and Pullup Characteristics 1. The full variation in driver pulldown current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve. 2. It is recommended that the “typical” IBIS pulldown V-I curve lie within the shaded region of the V-I curve. 3. The full variation in driver pullup current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve. 4. It is recommended that the “typical” IBIS pullup V-I curve lie within the shaded region of the V-I curve. IOHW Output Current: Weak Strength Driver High current (VOUT= VDDQ -0.763V, min VREF, min VTT) Low current (VOUT= 0.763V, max VREF, max VTT) − 9.0 mA 1 IOLW 9.0 Normal Strength Driver Pulldown Characteristics DC Electrical Characteristics and Operating Conditions (0°C ≤ TA ≤ 70°C; VDDQ = 2.5V ± 0.2V, VDD = + 2.5V ± 0.2V, see AC Characteristics) Symbol Parameter Min Max Units Notes 1. Inputs are not recognized as valid until VREF stabilizes. 2. VREF is expected to be equal to 0.5 VDDQ of the transmitting device, and to track variations in the DC level of the same. Peak-to-peak noise on VREF may not exceed ± 2% of the DC value. 3. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF, and must track variations in the DC level of VREF. 4. VID is the magnitude of the difference between the input level on CK and the input level on CK 5. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the entire tempera-ture and voltage range, for device drain to source voltages for 0.25 volts to 1.0 volts. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation. 0 2.7 0 140 VOUT (V) Maximum Typical High Typical Low Minimum |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |