| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PC8374L bảng dữ liệu(PDF) 76 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
PC8374L bảng dữ liệu(HTML) 76 Page - National Semiconductor (TI) |
|
76 / 239 page ![]() 3.0 Device Architecture and Configuration (Continued) www.national.com 76 Revision1.1 Table 31. Reset Values for PUPCTL and PDNCTL Bits 6 R/W or RO EVDBNC (Event Debounce Enable). Enables the debounce circuit in the event input path of the selected GPIO pin. The event is detected after a predetermined debouncing period (see Section 6.3 on page 113). 0: Disabled (default) 1: Enabled Reserved for Port 1, Pin 5. 5 R/W or RO EVPOL (Event Polarity). Defines the polarity of the wake-up signal that issues an event from the selected GPIO pin (see Section 6.3 on page 113). 0: Falling edge or low level input (default) 1: Rising edge or high level input Reserved for Port 1, Pin 5. 4 R/W or RO EVTYPE (Event Type). Defines the type of the wake-up signal that issues an event from the selected GPIO pin (see Section 6.3 on page 113). 0: Edge input (default) 1: Level input Reserved for Port 1, Pin 5. 3 R/W1S LOCKCFP (Lock Configuration of Pin). When set to 1, locks the GPIO pin configuration and data (also see Section 6.4 on page 115) by disabling writing to itself, to GPCFG1 register bits PDNCTL, PUPCTL, OUTTYPE and OUTENA, to all of the bits of GPCFG2 register and to the corresponding bit in GPDO and GPDIO registers. Once set, this bit can be cleared by Hardware reset. 0: R/W bits are enabled for write (default) 1: All bits are RO 2 R/W or RO PUPCTL (Pull-Up Control). Controls the internal pull-up resistor of the selected GPIO pin (see Section 6.2 on page 111). 0: Disabled (for default value, see Table 31) 1: Enabled (for default value, see Table 31) Undefined results when both the PDNCTL bit and the PUPCTL bit are set to 1. 1 R/W or RO OUTTYPE (Output Type). Controls the output buffer type of the selected GPIO pin (see Section 6.2 on page 111). 0: Open-drain (default) 1: Push-pull 0 R/W or RO OUTENA (Output Enable). Controls the output buffer of the selected GPIO pin (see Section 6.2 on page 111). 0: TRI-STATE (default) 1: Output buffer enabled GP(I)O(E)nn 00 01-06 07 10 11-13 14 15-16 17 PUPCTL 010 0 1 0 0 1 PDNCTL 1 No Pull-Down 1 No Pull-Down 1 No Pull-Down Bit Type Description Winbond Electronics Corp. Advanced PC Product Center |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |