| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LTM4664 bảng dữ liệu(PDF) 111 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
LTM4664 bảng dữ liệu(HTML) 111 Page - Analog Devices |
|
111 / 138 page ![]() LTM4664A 111 Rev. 0 For more information www.analog.com PMBus COMMAND DETAILS The UV fault and warn are masked until the following criteria are achieved: 1) The TON_MAX_FAULT_LIMIT has been reached 2) The TON_DELAY sequence has completed 3) The TON_RISE sequence has completed 4) The VOUT_UV_FAULT_LIMIT threshold has been reached 5) The IOUT_OC_FAULT_LIMIT is not present The UV fault and warn are masked whenever the channel is not active. The UV fault and warn are masked during TON_RISE and TOFF_FALL sequencing. This command has one data byte. Table 15. VOUT_UV_FAULT_RESPONSE Data Byte Contents BITS DESCRIPTION VALUE MEANING 7:6 Response For all values of bits [7:6], the LTM4664A: • Sets the corresponding fault bit in the status commands and • Notifies the host by asserting ALERT pin, unless masked. The fault bit, once set, is cleared only when one or more of the following events occurs: • The device receives a CLEAR_FAULTS command. • The output is commanded through the RUN pin, the OPERATION command, or the combined action of the RUN pin and OPERATION command, to turn off and then to turn back on, or • The device receives a RESTORE_USER_ALL command. • The device receives a MFR_RESET command. • The device supply power is cycled. 00 The PMBus device continues operation without interruption. (Ignores the fault functionally) 01 The PMBus device continues operation for the delay time specified by bits [2:0] and the delay time unit specified for that particular fault. If the fault condition is still present at the end of the delay time, the unit responds as programmed in the Retry Setting (bits [5:3]). 10 The device shuts down (disables the output) and responds according to the retry setting in bits [5:3]. 11 Not supported. Writing this value will generate a CML fault. 5:3 Retry Setting 000 The unit does not attempt to restart. The output remains disabled until the fault is cleared until the device is commanded OFF bias power is removed. 111 The PMBus device attempts to restart continuously, without limitation, until it is commanded OFF (by the RUN pin or OPERATION command or both), bias power is removed, or another fault condition causes the unit to shut down without retry. Note: The retry interval is set by the MFR_RETRY_DELAY command. 2:0 Delay Time 000-111 The delay time in 10µs increments. This delay time determines how long the controller continues operating after a fault is detected. Only valid for deglitched off state. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |