công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

LTM4664 bảng dữ liệu(PDF) 22 Page - Analog Devices

tên linh kiện LTM4664
Giải thích chi tiết về linh kiện  30V to 58V Input, Dual 30A, Single 60A 關Module Regulator with Digital Power System Management
PDF  138 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  AD [Analog Devices]
Trang chủ  http://www.analog.com
Logo AD - Analog Devices

LTM4664 bảng dữ liệu(HTML) 22 Page - Analog Devices

Back Button LTM4664 Datasheet HTML 18Page - Analog Devices LTM4664 Datasheet HTML 19Page - Analog Devices LTM4664 Datasheet HTML 20Page - Analog Devices LTM4664 Datasheet HTML 21Page - Analog Devices LTM4664 Datasheet HTML 22Page - Analog Devices LTM4664 Datasheet HTML 23Page - Analog Devices LTM4664 Datasheet HTML 24Page - Analog Devices LTM4664 Datasheet HTML 25Page - Analog Devices LTM4664 Datasheet HTML 26Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 22 / 138 page
background image
LTM4664A
22
Rev. 0
For more information www.analog.com
PIN FUNCTIONS
to configure the LTM4664A’s Channel 0 output to pow-
er-up to a VOUT_COMMAND value (and associated output
voltage monitoring and protection/fault-detection thresh-
olds) different from those of NVM contents. (See the 4:1
Divider Application Information section.) Minimize capac-
itance especially when the pin is left open to assure accu-
rate detection of the pin state. Note that use of RCONFIGs
on VOUTC0_CFG/VTRIMC0_CFG can affect the VOUTC0
range setting (MFR_PWM_MODE0 [1]) and loop gain.
VOUTC1_CFG (J7): Output Voltage Select Pin for VOUTC1,
Coarse Setting. If the VOUTC1_CFG and VTRIMC1_CFG
pins are both left open or, if the LTM4664A is config-
ured to ignore pin-strap (RCONFIG) resistors, i.e., MFR_
CONFIG_ALL [6] = 1b then the LTM4664A’s target VOUTC1
output voltage setting (VOUT_COMMAND1) and associ-
ated OV/UV warning and fault thresholds are dictated at
SVIN power up according to the LTM4664A’s NVM con-
tents, in precisely the same fashion that the VOUTC1_CFG
and VTRIMC1_CFG pins affect the respective settings of
VOUT1/Channel 1. (See VOUTC1_CFG, VTRIMC1_CFG and
the 4:1 Divider Application Information section.) Minimize
capacitance—especially when the pin is left open—to
assure accurate detection of the pin state. Note that use
of RCONFIGs on VOUTC1_CFG/VTRIMC1_CFG can affect
the VOUTC1 range setting (MFR_PWM_MODE1 [1]) and
loop gain. A resistor divider from VDD25 to SGND_C0_C1.
See page 43.
ASEL (J8): Serial Bus Address Configuration Pin. On any
given I2C/SMBus serial bus segment, every device
must have its own unique slave address. If this pin is
left open, the LTM4664A powers up to a slave address
set by MFR_ADDRESS[6:0] (see Table  4). The facto-
ry-default setting is 0x4F (hexadecimal), i.e., 1001111b
(industry standard convention is used throughout this
document: 7-bit slave addressing). The lower four bits of
the LTM4664A’s slave address can be altered from the
NVM-set value by connecting a resistor from this pin to
SGND. Minimize capacitance—especially when the pin is
left open—to assure accurate detection of the pin state.
See 4:1 Divider Application Information section.
RUN_C0, RUN_C1 (J9, K8 Respectively): Enable Run
Input for Channels 0 and 1, respectively. Open-drain input
and output. Logic high on these pins enables the respective
outputs of the LTM4664A. These open-drain output pins
hold the pin low until the LTM4664A is out of reset and
VIN3_C1 is detected to exceed VIN_ON. A pull-up resis-
tor to 3.3V is required in the application. The LTM4664A
pulls RUN_C0 and/or RUN_C1 low, as appropriate, when
a global fault and/or channel-specific fault occurs whose
fault response is configured to latch off and cease reg-
ulation; issuing a CLEAR_FAULTS command via I2C or
power cycling SVIN is necessary to restart the module, in
such cases. Do not pull RUN logic high with a low imped-
ance source. Use PGOODS2 and FAULTS2 to sequence on
RUN_C0, and RUN_C1 for the dual 25A/30A stage.
ALERT (J10): Open-Drain Digital Output. A pull-up
resistor to 3.3V is required in the application only if
SMBALERT interrupt detection is implemented in one’s
SMBus system.
VTRIMC0_CFG (K5): Output Voltage Select Pin for VOUTC0,
Fine Setting. Works in combination with VOUTC0_CFG
to affect the VOUT_COMMAND (and associated output
voltage monitoring and protection/fault-detection thresh-
olds) of Channel 0, at SVIN power-up. (See VOUTC0_CFG
and the Dual 25A/30A PSM Applications Information sec-
tion.) Minimize capacitance especially when the pin is left
open to assure accurate detection of the pin state. Note
that use of RCONFIGs on VOUTC0_CFG/VTRIMC0_CFG
can affect the VOUTC0 range setting (MFR_PWM_MODE0
[1]) and loop gain.
VDD25 (K6): Internally Generated 2.5V Power Supply
Output Pin. Do not load this pin with external current;
it is used strictly to bias internal logic and provides cur-
rent for the internal pull-up resistors connected to the
configuration-programming pins. No external decoupling
is required.
WP (K7): Write Protect Pin, Active High. An internal 10μA
current source pulls this pin to VDD33. If WP is open cir-
cuit or logic high, only I2C writes to PAGE, OPERATION,
CLEAR_FAULTS, MFR_CLEAR_PEAKS and MFR_EE_
UNLOCK are supported. Additionally, Individual faults
can be cleared by writing 1b’s to bits of interest in reg-
isters prefixed with “STATUS”. If WP is low, I2C writes
are unrestricted.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com