công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

LTM4664 bảng dữ liệu(PDF) 61 Page - Analog Devices

tên linh kiện LTM4664
Giải thích chi tiết về linh kiện  30V to 58V Input, Dual 30A, Single 60A 關Module Regulator with Digital Power System Management
PDF  138 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  AD [Analog Devices]
Trang chủ  http://www.analog.com
Logo AD - Analog Devices

LTM4664 bảng dữ liệu(HTML) 61 Page - Analog Devices

Back Button LTM4664 Datasheet HTML 57Page - Analog Devices LTM4664 Datasheet HTML 58Page - Analog Devices LTM4664 Datasheet HTML 59Page - Analog Devices LTM4664 Datasheet HTML 60Page - Analog Devices LTM4664 Datasheet HTML 61Page - Analog Devices LTM4664 Datasheet HTML 62Page - Analog Devices LTM4664 Datasheet HTML 63Page - Analog Devices LTM4664 Datasheet HTML 64Page - Analog Devices LTM4664 Datasheet HTML 65Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 61 / 138 page
background image
LTM4664A
61
Rev. 0
For more information www.analog.com
PMBus COMMAND SUMMARY
COMMAND NAME
CMD
CODE DESCRIPTION
TYPE
PAGED
DATA
FORMAT UNITS NVM
DEFAULT
VALUE
PAGE
MFR_IOUT_CAL_GAIN
0xDA The ratio of the voltage at the current
sense pins to the sensed current. For
devices using a fixed current sense
resistor. It is the resistance value in mohm.
OxAA8B set at factory
R Word
Y
L11
0.350mΩ
102
MFR_PADS
0xE5 Digital status of the I/O pads.
R Word
N
Reg
Y
NA
124
MFR_ADDRESS
0xE6 Sets the 7-bit I2C address byte.
R/W Byte
N
Reg
Y
0x4F
92
MFR_SPECIAL_ID
0xE7 Manufacturer code representing the
LTM4664A and revision
R Word
N
Reg
0x4100
118
MFR_IIN_CAL_GAIN
0xE8 The resistance value of the input current
sense element in mΩ.
R/W Word
N
L11
mΩ
Y
2.0
0xC200
104
MFR_FAULT_LOG_ STORE
0xEA Command a transfer of the fault log from
RAM to EEPROM.
Send Byte
N
NA
131
MFR_INFO
0xB6 Contact factory.
135
MFR_FAULT_LOG_ CLEAR
0xEC Initialize the EEPROM block reserved for
fault logging.
Send Byte
N
NA
135
MFR_FAULT_LOG
0xEE Fault log data bytes.
R Block
N
Reg
Y
NA
131
MFR_COMMON
0xEF Manufacturer status bits that are common
across multiple LTC chips.
R Byte
N
Reg
NA
125
MFR_COMPARE_USER_ ALL
0xF0 Compares current command contents
with NVM.
Send Byte
N
NA
130
MFR_TEMPERATURE_2_ PEAK 0xF4 Peak internal die temperature since last
MFR_ CLEAR_PEAKS.
R Word
N
L11
C
NA
129
MFR_PWM_CONFIG
0xF5 Set numerous parameters for the DC/DC
controller including phasing.
R/W Byte
N
Reg
Y
0x10
97
MFR_IOUT_CAL_GAIN_ TC
0xF6 Temperature coefficient of the current
sensing element.
R/W Word
Y
CF
ppm/
˚C
Y
3900
0x0F3C
102
MFR_RVIN
0xF7 The resistance value of the VIN pin filter
element in mΩ. Set at Factory
R Word
N
L11
mΩ
N
1000
0x03E8
99
MFR_TEMP_1_GAIN
0xF8 Sets the slope of the external temperature
sensor.
R/W Word
Y
CF
Y
0.9
0x3FAE
105
MFR_TEMP_1_OFFSET
0xF9 Sets the offset of the external temperature
sensor with respect to –273.1°C
R/W Word
Y
L11
C
Y
0.0
0x8000
105
MFR_RAIL_ADDRESS
0xFA Common address for PolyPhase outputs
to adjust common parameters.
R/W Byte
Y
Reg
Y
0x80
92
MFR_REAL_TIME
0xFB 48-bit share-clock counter value.
R Block
N
CF
NA
xx
MFR_RESET
0xFD Commanded reset without requiring a
power down.
Send Byte
N
NA
94
Note 1. Commands indicated with Y in the NVM column indicate that these commands are stored and restored using the STORE_USER_ALL and
RESTORE_USER_ALL commands, respectively.
Note 2. Commands with a default value of NA indicate “not applicable”. Commands with a default value of FS indicate “factory set on a per part basis”.
Note 3. The LTM4664A contains additional commands not listed in Table 7. Reading these commands is harmless to the operation of the IC; however, the
contents and meaning of these commands can change without notice.
Note 4. Some of the unpublished commands are read-only and will generate a CML bit 6 fault if written.
Note 5. Writing to commands not published in Table 7 is not permitted.
Note 6. The user should not assume compatibility of commands between different parts based upon command names. Always refer to the manufacturer’s
data sheet for each part for a complete definition of a command’s function. LTC strives to keep command functionality compatible between all LTC
devices. Differences may occur to address specific product requirements.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com