| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MCF5373CAB180 bảng dữ liệu(PDF) 18 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
MCF5373CAB180 bảng dữ liệu(HTML) 18 Page - NXP Semiconductors |
|
18 / 46 page ![]() MCF537x ColdFire® Microprocessor Data Sheet, Rev. 4 Electrical Characteristics Freescale Semiconductor 18 5.6 External Interface Timing Characteristics Table 9 lists processor bus input timings. NOTE All processor bus timings are synchronous; that is, input setup/hold and output delay with respect to the rising edge of a reference clock. The reference clock is the FB_CLK output. All other timing relationships can be derived from these values. Timings listed in Table 9 are shown in Figure 7 and Figure 8. 14 Discrete load capacitance for EXTAL CL_EXTAL 2*CL–- CS_EXTAL – CPCB_EXTAL 7 pF 17 CLKOUT Period Jitter, 3, 4, 7, 8, 9 Measured at fSYS Max Peak-to-peak Jitter (Clock edge to clock edge) Long Term Jitter Cjitter — — 10 TBD % fsys/3 % fsys/3 18 Frequency Modulation Range Limit 3, 10, 11 (fsysMax must not be exceeded) Cmod 0.8 2.2 %fsys/3 19 VCO Frequency. fvco = (fref * PFD)/4 fvco 350 540 MHz 1 The maximum allowable input clock frequency when booting with the PLL enabled is 24MHz. For higher input clock frequencies the processor must boot in LIMP mode to avoid violating the maximum allowable CPU frequency. 2 All internal registers retain data at 0 Hz. 3 This parameter is guaranteed by characterization before qualification rather than 100% tested. 4 Proper PC board layout procedures must be followed to achieve specifications. 5 This parameter is guaranteed by design rather than 100% tested. 6 This specification is the PLL lock time only and does not include oscillator start-up time. 7 C PCB_EXTAL and CPCB_XTAL are the measured PCB stray capacitances on EXTAL and XTAL, respectively. 8 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f sys. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the PLL circuitry via PLL VDD, EVDD, and VSS and variation in crystal oscillator frequency increase the Cjitter percentage for a given interval. 9 Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of Cjitter+Cmod. 10 Modulation percentage applies over an interval of 10 μs, or equivalently the modulation rate is 100 KHz. 11 Modulation range determined by hardware design. Table 8. PLL Electrical Characteristics (continued) Num Characteristic Symbol Min. Value Max. Value Unit |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |