| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
98ASH70029A bảng dữ liệu(PDF) 10 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
98ASH70029A bảng dữ liệu(HTML) 10 Page - NXP Semiconductors |
|
10 / 36 page ![]() Table 3. DC characteristics (continued) Symbol C Descriptions Min Typical1 Max Unit |IOZ| P Hi-Z (off- state) leakage current All input/output (per pin) VIN = VDD or VSS — 0.1 1 µA |IOZTOT| C Total leakage combined for all inputs and Hi-Z pins All input only and I/O VIN = VDD or VSS — — 2 µA RPU P Pullup resistors All digital inputs, when enabled (all I/O pins other than PTA2 and PTA3) — 30.0 — 50.0 kΩ RPU3 P Pullup resistors PTA2 and PTA3 pin — 30.0 — 60.0 kΩ IIC D DC injection current4, 5, 6 Single pin limit VIN < VSS, VIN > VDD -0.2 — 2 mA Total MCU limit, includes sum of all stressed pins -5 — 25 CIn C Input capacitance, all pins — — — 7 pF VRAM C RAM retention voltage — 2.0 — — V 1. Typical values are measured at 25 °C. Characterized, not tested. 2. Only PTB4, PTB5, PTD0, PTD1 support ultra high current output. 3. The specified resistor value is the actual value internal to the device. The pullup value may appear higher when measured externally on the pin. 4. All functional non-supply pins, except for , are internally clamped to VSS and VDD. 5. Input must be current-limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the large one. 6. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If the positive injection current (VIn > VDD) is higher than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure that external VDD load will shunt current higher than maximum injection current when the MCU is not consuming power, such as no system clock is present, or clock rate is very low (which would reduce overall power consumption). Table 4. LVD and POR Specification Symbol C Description Min Typ Max Unit VPOR D POR re-arm voltage1, 2 1.5 1.75 2.0 V VLVDH C Falling low-voltage detect threshold - high range (LVDV = 1)3 4.2 4.3 4.4 V VLVW1H C Falling low- voltage warning threshold - high range Level 1 falling (LVWV = 00) 4.3 4.4 4.5 V VLVW2H C Level 2 falling (LVWV = 01) 4.5 4.5 4.6 V VLVW3H C Level 3 falling (LVWV = 10) 4.6 4.6 4.7 V VLVW4H C Level 4 falling (LVWV = 11) 4.7 4.7 4.8 V Table continues on the next page... Nonswitching electrical specifications MC9S08PA16 Series Data Sheet, Rev. 4, 03/2020 10 NXP Semiconductors |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |