| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
98ASH70029A bảng dữ liệu(PDF) 22 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
98ASH70029A bảng dữ liệu(HTML) 22 Page - NXP Semiconductors |
|
22 / 36 page ![]() Table 11. XOSC and ICS specifications (temperature range = -40 to 105 °C for V part and -40 to 125 °C for M part ambient) (continued) Num C Characteristic Symbol Min Typical1 Max Unit 8 D Square wave input clock frequency FEE or FBE mode2 fextal 0.03125 — 5 MHz D FBELP mode 0 — 20 MHz 9 P Average internal reference frequency - trimmed fint_t — 31.25 — kHz 10 P DCO output frequency range - trimmed fdco_t 16 — 20 MHz 11 P Total deviation of DCO output from trimmed frequency5 Over full voltage and temperature range Δfdco_t — — ±2.0 %fdco C Over fixed voltage and temperature range of 0 to 70 °C ±1.0 12 C FLL acquisition time5, 7 tAcquire — — 2 ms 13 C Long term jitter of DCO output clock (averaged over 2 ms interval)8 CJitter — 0.02 0.2 %fdco 1. Data in Typical column was characterized at 5.0 V, 25 °C or is typical recommended value. 2. When ICS is configured for FEE or FBE mode, input clock source must be divisible using RDIV to within the range of 31.25 kHz to 39.0625 kHz. 3. See crystal or resonator manufacturer's recommendation. 4. Load capacitors (C1,C2), feedback resistor (RF) and series resistor (RS) are incorporated internally when RANGE = HGO = 0. 5. This parameter is characterized and not tested on each device. 6. Proper PC board layout procedures must be followed to achieve specifications. 7. This specification applies to any time the FLL reference source or reference divider is changed, trim value changed, or changing from FLL disabled (FBELP, FBILP) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 8. Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fBus. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage for a given interval. XOSC EXTAL XTAL Crystal or Resonator RS C2 RF C1 Figure 16. Typical crystal or resonator circuit Peripheral operating requirements and behaviors MC9S08PA16 Series Data Sheet, Rev. 4, 03/2020 22 NXP Semiconductors |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |