| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ACT88326VA bảng dữ liệu(PDF) 30 Page - Active-Semi, Inc |
|
|
|||||||||||||||||||||||||||||
ACT88326VA bảng dữ liệu(HTML) 30 Page - Active-Semi, Inc |
|
30 / 41 page ![]() ACT88326VA Rev 1.0, 29-May-2018 Innovative PowerTM www.active-semi.com ActiveSwitcherTM is a trademark of Active-Semi. Copyright © 2018 Active-Semi, Inc 30 Current Limit Because LSG only connects to the external FET gate, Load Switch does not have a current limit function. The input to the Load Switch should come from an ACT88326 Buck, LDO, or other current limited source. Load Switch POK The load switch internal Power OK, POK, signal can be used in the sequencing of other power supplies. The load switch POK signal goes active when the load switch gate drive voltage at the LSG pin is greater than VIN + 1V and VIN – VOUT < 100mV. Note that the ac- tual load switch may or may not be fully on at this time depending on the FET used for the load switch or any additional filtering or delay circuitry connected to LSG. PC board layout guidance Proper parts placement and PCB layout are critical to the operation of switching power supplies. Follow the following layout guidelines when designing the ACT88326 PCB. Refer to the Active-Semi ACT88326 Evaluation Kits for layout examples 1. Place the buck input capacitors as close as possible to the IC. Refer to the Pin Descriptions for each buck converter’s dedicated VINx and PGNDx pins. Connect the input capacitors di- rectly to the corresponding VINx and PGNDx power ground pin on the top layer. Routing these traces on the top layer eliminates the need for vias. 2. Minimize the switch node trace length between each SW_Bx pin and the inductor. Optimal switch node routing is to run the trace between the input capacitor’s pads. Using 0805 sized in- put capacitors is recommended. Avoid routing sensitive analog signals near these high fre- quency, high dV/dt traces. 3. Place the LDO input capacitor close to the AVIN pin. Connect the capacitor directly to AVIN and AGND on the top layer. 4. The Buck output capacitors should be placed by the inductor and connected directly to the in- ductor and ground plane with short and wide traces. The output capacitor ground should make a short connection to the input capacitor ground. If required, use multiple vias. 5. Each regulator’s FB_Bx should be Kelvin con- nected to its output capacitor through the short- est possible route, while keeping sufficient dis- tance from switching nodes to prevent noise in- jection. The IC regulates the output voltage to this Kelvin connection. 6. The PGNDx and AGND ground pins must be electrically connected together. Because the AGND ground plane is used for analog, digital, and LDO grounds, it does not need to be com- pletely isolated from the rest of the PCB grounds. However, take care to avoid routing the buck converter switching currents through the analog ground connections. 7. Connect the VIN_IO input capacitor to the AGND ground pin. 8. Remember that all open drain outputs need pull-up resistors. 9. Figure 4 shows the recommended power and signal connections and routing from under the IC. Refer to the ACT88326 evaluation kit for a full, detailed routing example. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |