công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

OL2385SWUG bảng dữ liệu(PDF) 37 Page - NXP Semiconductors

tên linh kiện OL2385SWUG
Giải thích chi tiết về linh kiện  SIGFOX software driver
PDF  64 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  NXP [NXP Semiconductors]
Trang chủ  http://www.nxp.com
Logo NXP - NXP Semiconductors

OL2385SWUG bảng dữ liệu(HTML) 37 Page - NXP Semiconductors

Back Button OL2385SWUG Datasheet HTML 33Page - NXP Semiconductors OL2385SWUG Datasheet HTML 34Page - NXP Semiconductors OL2385SWUG Datasheet HTML 35Page - NXP Semiconductors OL2385SWUG Datasheet HTML 36Page - NXP Semiconductors OL2385SWUG Datasheet HTML 37Page - NXP Semiconductors OL2385SWUG Datasheet HTML 38Page - NXP Semiconductors OL2385SWUG Datasheet HTML 39Page - NXP Semiconductors OL2385SWUG Datasheet HTML 40Page - NXP Semiconductors OL2385SWUG Datasheet HTML 41Page - NXP Semiconductors Next Button
Zoom Inzoom in Zoom Outzoom out
 37 / 64 page
background image
NXP Semiconductors
OL2385SWUG
SIGFOX software driver
OL2385SWUG
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2018. All rights reserved.
User guide
Rev. 2.1 — 6 April 2018
37 / 64
7.2 OL2385 Transceiver Initialization Sequence
After you have set up the KL43Z board according to Section 5.4.1 "Setting up KL43Z
board with terminal program", you are now ready to use the terminal to control the
OL2385 board. In order to do so, the following sections have to be understood.
Figure 26. SPI commands to control OL2385
7.2.1 Mandatory initialization sequence
The following sequence of commands is a
mandatory initialization sequence that must
be executed after power-on/reset of the OL2385 board.
7.2.1.1 Wakeup from low-power mode
A Send wakeup command has to be sent to the device first after any kind of software
device reset, power on/off reset or battery-on reset. By default, the device goes
immediately to low-power SLEEP mode after any of these resets or after the explicit SPI
command Send to sleep. The CS pin of the SPI interface is the wakeup pin and has to be
driven low by the MCU to wake the device up. This is done by a Send wakeup command,
including two bytes transfer as per SPI protocol. This has to be done only once after the
reset until the next reset. Once done until the next reset, other commands can be used.
Note: Before proceeding to the low-power mode, OL2385 configures all of its pins
to a pulled-down configuration, except for CS and ACK pins of SPI—these pins are
pulled high. For the low-power mode to work properly without any leakage current, it is
important to have the same settings of the pins on the MCU side. All pins on the MCU
should be pulled low and only CS and ACK should be high.
Note: The Send Wakeup command does not return an acknowledgment RX frame back.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com