| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
68HC908RF bảng dữ liệu(PDF) 48 Page - Motorola, Inc |
|
|
|||||||||||||||||||||||||||||
68HC908RF bảng dữ liệu(HTML) 48 Page - Motorola, Inc |
|
48 / 188 page ![]() Computer Operating Properly Module (COP) Data Sheet MC68HC908RF2 — Rev. 4.0 48 Computer Operating Properly Module (COP) MOTOROLA The COP counter is a free-running 6-bit counter preceded by a 12-bit prescaler. If not cleared by software, the COP counter overflows and generates an asynchronous reset after 213 –24 or 218 –24 CGMXCLK cycles, depending on the state of the COP rate select bit, COPRS, in the configuration register. When COPRS = 1, a 4.9152-MHz crystal gives a COP timeout period of 53.3 ms. Writing any value to location $FFFF before an overflow occurs prevents a COP reset by clearing the COP counter and stages 5 through 12 of the prescaler. NOTE: Service the COP immediately after reset and before entering or after exiting stop mode to guarantee the maximum time before the first COP counter overflow. A COP reset pulls the RST pin low for 32 CGMXCLK cycles and sets the COP bit in the SIM reset status register (SRSR). In monitor mode, the COP is disabled if the RST pin or the IRQ pin is held at VTST. During the break state, VTST on the RST pin disables the COP. NOTE: Place COP clearing instructions in the main program and not in an interrupt subroutine. Such an interrupt subroutine could keep the COP from generating a reset even while the main program is not working properly. 4.3 I/O Signals The following paragraphs describe the signals shown in Figure 4-1. 4.3.1 CGMXCLK CGMXCLK is the oscillator output signal. See 6.3.5 Clock Selection Circuit for a description of CGMXCLK. 4.3.2 STOP Instruction The STOP instruction clears the COP prescaler. 4.3.3 COPCTL Write Writing any value to the COP control register (COPCTL) (see 4.4 COP Control Register) clears the COP counter and clears stages 12 through 5 of the COP prescaler. Reading the COP control register returns the reset vector. 4.3.4 Power-On Reset The power-on reset (POR) circuit clears the COP prescaler 4096 CGMXCLK cycles after power-up. 4.3.5 Internal Reset An internal reset clears the COP prescaler and the COP counter. Freescale Semiconductor, Inc. For More Information On This Product, Go to: www.freescale.com |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |