STM32F398VE datasheet(134/151 Pages) STMICROELECTRONICS

134 / 151 page

Electrical characteristics

STM32F398VE

134/151

DocID027227 Rev 2

SINAD

(5)

Signal-to-

noise and

distortion

ratio

ADC clock freq.

72 MHz,

Sampling freq.

5 Msps,

1.8 V

VDDA, VREF+ 3.6 V

100-pin package

Single

Ended

Fast channel 5.1 Ms

Slow channel 4.8 Ms

Differential

Fast channel 5.1 Ms

Slow channel 4.8 Ms

SNR(5)

Signal-to-

noise ratio

Single

Ended

Fast channel 5.1 Ms

Slow channel 4.8 Ms

Differential

Fast channel 5.1 Ms

Slow channel 4.8 Ms

THD(5)

Total

harmonic

distortion

Single

Ended

Fast channel 5.1 Ms

Slow channel 4.8 Ms

-74

Differential

Fast channel 5.1 Ms

-78

Slow channel 4.8 Ms

-76

1. ADC DC accuracy values are measured after internal calibration.

2. ADC accuracy vs. negative Injection Current: Injecting negative current on any analog input pins should be avoided as this

significantly reduces the accuracy of the conversion being performed on another analog input. It is recommended to add a

Schottky diode (pin to ground) to analog pins which may potentially inject negative current.



Any positive injection current within the limits specified for IINJ(PIN) and IINJ(PIN) in Section 6.3.14 does not affect the ADC

accuracy.

3. Better performance may be achieved in restricted VDDA, frequency and temperature ranges.

4. Data based on characterization results, not tested in production.

5. Value measured with a -0.5 dB full scale 50 kHz sine wave input signal.

Table 76. ADC accuracy, 100-pin packages- limited test conditions (1)(2)(3) (continued)

Symbol Parameter

Conditions

Min (4)

Max(4)

Unit

Table 77. ADC accuracy at 1MSPS(1)(2)

Symbol

Parameter

Test conditions

Typ

Max(3)

Unit

Total unadjusted error

ADC Freq ≤ 72 MHz



Sampling Freq ≤ 1MSPS



2.4 V ≤ VDDA = VREF+ ≤ 3.6 V

Single-ended mode

Fast channel

±2.5

±5

LSB

Slow channel

±3.5

±5

Offset error

Fast channel

±1

±2.5

Slow channel

±1.5

±2.5

Gain error

Fast channel

±2

±3

Slow channel

±3

±4

Differential linearity error

Fast channel

±0.7

±2

Slow channel

±0.7

±2

Integral linearity error

Fast channel

±1

±3

Slow channel

±1.2

±3

1. ADC DC accuracy values are measured after internal calibration.

2. ADC accuracy vs. negative Injection Current: Injecting negative current on any analog input pins should be avoided as this

significantly reduces the accuracy of the conversion being performed on another analog input. It is recommended to add a

Schottky diode (pin to ground) to analog pins which may potentially inject negative current. Any positive injection current

within the limits specified for IINJ(PIN) and ∑IINJ(PIN) in Section 6.3.14: I/O port characteristics does not affect the ADC

accuracy.

STM32F398VE bảng dữ liệu(PDF) 134 Page - STMicroelectronics

STM32F398VE bảng dữ liệu(HTML) 134 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL