STM32F413CH datasheet(87/207 Pages) STMICROELECTRONICS

87 / 207 page

DocID029162 Rev 2

87/207

STM32F413xG/H

Electrical characteristics

174

Typical and maximum current consumption

The MCU is placed under the following conditions:

•

All I/O pins are in input mode with a static value at VDD or VSS (no load).

•

All peripherals are disabled except if it is explicitly mentioned.

•

The Flash memory access time is adjusted to both fHCLK frequency and VDD ranges

(refer to Table 17: Features depending on the operating power supply range).

•

The voltage scaling is adjusted to fHCLK frequency as follows:

–

Scale 3 for fHCLK ≤ 64 MHz

–

Scale 2 for 64 MHz < fHCLK ≤ 84 MHz

–

Scale 1 for 84 MHz < fHCLK ≤ 100 MHz

•

The system clock is HCLK, fPCLK1 = fHCLK/2, and fPCLK2 = fHCLK.

•

External clock is 4 MHz and PLL is ON except if it is explicitly mentioned.

•

The maximum values are obtained for VDD = 3.6 V and a maximum ambient

temperature (TA), and the typical values for TA= 25 °C and VDD = 3.3 V unless

otherwise specified.

Table 22. Typical and maximum current consumption, code with data processing (ART

accelerator disabled) running from SRAM - VDD = 1.7 V

Symbol Parameter

Conditions

fHCLK

(MHz)

Typ

Max(1)

Unit

TA= 25 °C TA= 25 °C TA=85 °C TA=105 °C TA=125 °C

IDD

Supply

current in

Run mode

External clock,

PLL ON,

all peripherals

enabled(2)(3)

100

32.9

34.96

35.30

37.21

40.79

26.5

28.13

28.58

30.50

33.96

18.3

19.44

20.11

21.76

25.03

14.4

15.28

16.12

17.95

21.11

7.5

8.10

9.35

11.09

14.38

6.4

6.99

8.17

9.96

13.17

HSI, PLL off, all

peripherals

enabled(2)(3)

4.6

5.17

6.42

8.28

11.46

0.7

1.28

2.64

4.30

7.66

External clock,

PLL ON, all

peripherals

disabled(3)

100

15.4

16.43

17.35

19.17

22.85

12.4

13.28

14.32

16.12

19.67

8.7

9.36

10.38

12.06

15.31

6.9

7.47

8.54

10.36

13.49

3.7

4.27

5.47

7.17

10.45

3.2

3.72

5.01

6.67

10.02

HSI, PLL off, all

peripherals

disabled(3)

2.3

2.80

4.05

5.90

9.07

0.6

1.14

2.51

4.16

7.51

1. Based on characterization, not tested in production unless otherwise specified

2. When analog peripheral blocks such as ADC, HSE, LSE, HSI, or LSI are ON, an additional power consumption has to be

considered.

STM32F413CH bảng dữ liệu(PDF) 87 Page - STMicroelectronics

STM32F413CH bảng dữ liệu(HTML) 87 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL