CS8420 datasheet(22/80 Pages) CIRRUS

22 / 80 page

CS8420

DS245PP2

the channel status decodes are from the A channel

(CHS = 0) or B channel (CHS = 1).

The PRO (professional) bit is extracted directly.

Also, for consumer data, the COPY (copyright) bit

is extracted, and the category code and L bits are

decoded to determine SCMS status, indicated by

the ORIG (original) bit. Finally, the AUDIO bit is

extracted, and used to set an AUDIO indicator, as

described in the Non-Audio Auto Detection section

below.

If 50/15 µs pre-emphasis is detected, then this is re-

flected in the state of the EMPH pin.

The encoded sample word length channel status

bits are decoded according to AES3-1992 or IEC

60958. If the AES3 receiver is the data source for

the SRC, then the SRC audio input data is truncated

according to the channel status word length set-

tings. Audio data routed to the serial audio output

port is unaffected by the word length settings; all

24 bits are passed on as received.

The Appendix: Channel Status and User Data Buff-

er Management (page 72) describes the overall

handling of CS and U data.

9.3

User Data Handling

The incoming user data is buffered in a user acces-

sible buffer. Various automatic modes of re-trans-

mitting received U data are provided. The

Appendix: Channel Status and User Data Buffer

Management (page 72) describes the overall han-

dling of CS and U data.

Received U data may also be output to the U pin,

under the control of a control register bit. Depend-

ing on the data flow and clocking options selected,

there may not be a clock available to qualify the U

data output. Figure 21 illustrates the timing.

If the incoming user data bits have been encoded as

Q-channel subcode, then the data is decoded and

presented in 10 consecutive register locations. An

interrupt may be enabled to indicate the decoding

of a new Q-channel block, which may be read via

the control port.

9.4

Non-Audio Auto Detection

Since it is possible to convey non-audio data in an

AES3 data stream, it is important to know whether

the incoming AES3 data stream is digital audio or

not. This information is typically conveyed in

channel status bit 1 (AUDIO), which is extracted

RCBL

out

VLRCK

C, U

Output

RCBL and C output are only available in hardware mode 5.

RCBL goes high 2 frames after receipt of a Z pre-amble, and is high for 16 frames.

VLRCK is a virtual word clock, which may not exist, but is used to illustrate the CU timing.

VLRCK duty cycle is 50%. VLRCK frequency is always equal to the incoming frame rate.

If no SRC is used, and the serial audio output port is in master mode, VLRCK = OLRCK.

If the serial audio output port is in slave mode, then VLRCK needs to be externally created, if required.

C, U transitions are aligned within 1% of VLRCK period to VLRCK edges

Figure 21. AES3 Receiver Timing for C & U pin output data

CS8420 bảng dữ liệu(PDF) 22 Page - Cirrus Logic

CS8420 bảng dữ liệu(HTML) 22 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

bảng dữ liệu tải về

Link URL