TUSB1002 datasheet(6/28 Pages) TI1

6 / 28 page

TUSB1002

SLLSEU4A – MAY 2016 – REVISED MAY 2016

www.ti.com

Product Folder Links: TUSB1002

Submit Documentation Feedback

6.5 Electrical Characteristics, Power Supply

over operating free-air temperature range (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

P(U0_SSP_1200mV)

TUSB1002 power under normal operation

in U0 operating a SuperSpeedPlus

datarate with linear range set to 1200mV.

At 10 Gbps; VCC supply stable; VCC = 3.3

V; VOD = 1200 mVpp; Pattern = CP9

340

P(U0_SSP_1000mV)

TUSB1002 power under normal operation

in U0 operating a SuperSpeedPlus

datarate with linear range set to 1000mV.

At 10 Gbps; VCC supply stable; VCC = 3.3

V; VOD = 1000 mVpp; Pattern = CP9

325

P(U0_SSP_900mV)

TUSB1002 power under normal operation

in U0 operating a SuperSpeedPlus

datarate with linear range set to 900mV.

At 10 Gbps; VCC supply stable; VCC = 3.3

V; VOD = 900 mVpp; Pattern = CP9

298

P(U0_SS_1200mV)

TUSB1002 power under normal operation

in U0 operating a SuperSpeed datarate.

At 5 Gbps; VCC supply stable; VCC = 3.3 V;

VOD = 1200 mVpp; Pattern = CP0.

340

P(U1)

TUSB1002 power when U1.

In U1; VCC supply stable; VCC = 3.3 V;

VOD = 1200 mVpp

340

P(U2U3)

TUSB1002 power when in U2/U3.

Both channels 1 and 2 in U2/U3; VCC

supply stable; VCC = 3.3 V;

P(U2U3_SLP)

TUSB1002 power when in U2/U3 and

SLP_S0# is low.

Both channels 1 and 2 in U2/U3; VCC

supply stable; VCC = 3.3 V;

0.850

P(DISCONNECT_NON

TUSB1002 power when no USB device

detected on both TX1P/N or TX2P/N.

RX1 and RX2 termination disabled; VCC

supply stable; VCC = 3.3 V

P(DISCONNECT_ONE

)

TUSB1002 power when a USB device

detected on either TX1P/N or TX2P/N but

not both.

Either RX1 or RX2 termination enabled

both not both enabled; VCC supply stable;

VCC = 3.3 V

P(DISCONNECT_SLP)

TUSB1002 power when no USB device

detected on either TX1P/N or TX2P/N and

SLP_S0# is low..

RX1 and RX2 termination disabled; VCC

supply stable; VCC = 3.3 V

0.850

P(SHUTDOWN)

TUSB1002 power when EN is asserted

low.;

VCC supply stable; VCC = 3.3 V, EN = 0

0.6

6.6 Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

4-Level Inputs (MODE, CFG1, CFG2,CH1_EQ1, CH1_EQ2, CH2_EQ1, CH2_EQ2 )

IIH

High level input current

VCC = 3.6 V; VIN = 3.6 V

μA

IIL

Low level input current

VCC = 3.6 V; VIN = 0 V

–160

–40

μA

VTH

Threshold 0 / R

VCC = 3.3 V

0.55

Threshold R/ Float

1.65

Threshold Float / 1

2.8

RPU

Internal pull-up resistance

kΩ

RPD

Internal pull-down resistance

kΩ

EN, SLP_S0# Input

VIH

High level input voltage

VCC = 3. V

1.7

VCC

VIL

Low level input voltage

VCC = 3.3 V

0.7

IIH

High level input current

VCC = 3.6 V, EN = 3.6 V

–10

µA

IIL

Low level input current

VCC = 3.6 V, EN = 0 V

–15

µA

R(EN-PU)

Internal pull-up resistance for EN and

SLP_S0#.

400

kΩ

USB3.1 RECEIVER INTERFACE (RX1P/N AND RX2P/N)

RL(RX-DIFF)

RX Differential return loss

SDD11 10 MHz at 90

Ω

–19

SDD11 2 GHz at 90

Ω

–14

SDD11 5 – 10 GHz at 90

Ω

–7

RL(RX-CM)

RX Common mode return loss

0.5 – 5 GHz at 90

Ω

–10

EQ(GAIN-10Gbps)

Equalization Gain

50 mVpp At 5 GHz

EQ(DC0)

DC Equalization Gain at 0dB setting.

500 mVpp VID at 100 MHz; 1200mV

Linear Range Setting; Refer to Table 3

-0.15

EQ(DC1)

DC Equalization Gain at +1dB setting.

500 mVpp VID at 100 MHz; 1200mV

Linear Range Setting;

0.80

TUSB1002 bảng dữ liệu(PDF) 6 Page - Texas Instruments

TUSB1002 bảng dữ liệu(HTML) 6 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

bảng dữ liệu tải về

Link URL