LM26LVCISD-080SLASHNOPB datasheet(7/33 Pages) TI1

7 / 33 page

LM26LV

www.ti.com

SNIS144F – JULY 2007 – REVISED FEBRUARY 2013

Electrical Characteristics

Unless otherwise noted, these specifications apply for +VDD = +1.6V to +5.5V. Boldface limits apply for TA = TJ = TMIN to

TMAX ; all other limits TA = TJ = 25°C.

Units

Symbol

Parameter

Conditions

Typical(1)

Limits(2)

(Limit)

GENERAL SPECIFICATIONS

Quiescent Power Supply

μA (max)

Current

5.5

°C (max)

Hysteresis

4.5

°C (min)

OVERTEMP DIGITAL OUTPUT

ACTIVE HIGH, PUSH-PULL

VDD ≥ 1.6V

Source

≤ 340 μA

VDD ≥ 2.0V

Source

≤ 498 μA

VDD − 0.2V

V (min)

VDD ≥ 3.3V

Source

≤ 780 μA

VOH

Logic "1" Output Voltage

VDD ≥ 1.6V

Source

≤ 600 μA

VDD ≥ 2.0V

Source

≤ 980 μA

VDD − 0.45V

V (min)

VDD ≥ 3.3V

Source

≤ 1.6 mA

BOTH OVERTEMP and OVERTEMP DIGITAL OUTPUTS

VDD ≥ 1.6V

Sink

≤ 385 μA

VDD ≥ 2.0V

Sink

≤ 500 μA

0.2

VDD ≥ 3.3V

Sink

≤ 730 μA

VOL

Logic "0" Output Voltage

V (max)

VDD ≥ 1.6V

Sink

≤ 690 μA

VDD ≥ 2.0V

Sink

≤ 1.05 mA

0.45

VDD ≥ 3.3V

Sink

≤ 1.62 mA

OVERTEMP DIGITAL OUTPUT

ACTIVE LOW, OPEN DRAIN

TA = 30 °C

0.001

Logic "1" Output Leakage

IOH

μA (max)

Current(3)

TA = 150 °C

0.025

VTEMP ANALOG TEMPERATURE SENSOR OUTPUT

Gain 1: If Trip Point = 0 - 69°C

−5.1

mV/°C

Gain 2: If Trip Point = 70 - 109°C

−7.7

mV/°C

VTEMP Sensor Gain

Gain 3: If Trip Point = 110 - 129°C

−10.3

mV/°C

Gain 4: If Trip Point = 130 - 150°C

−12.8

mV/°C

Source

≤ 90 μA

−0.1

−1

mV (max)

(VDD − VTEMP) ≥ 200 mV

1.6V

≤ VDD < 1.8V

Sink

≤ 100 μA

0.1

mV (max)

VTEMP ≥ 260 mV

VTEMP Load Regulation

(4)

Source

≤ 120 μA

−0.1

−1

mV (max)

(VDD − VTEMP) ≥ 200 mV

VDD ≥ 1.8V

Sink

≤ 200 μA

0.1

mV (max)

VTEMP ≥ 260 mV

Source or Sink = 100

μA

Ω

0.29

VDD Supply- to-VTEMP

VDD = +1.6V to +5.5V

μV/V

DC Line Regulation(5)

−82

VTEMP Output Load

Without series resistor. See CAPACITIVE LOADS

1100

pF (max)

Capacitance

(1)

Typicals are at TJ = TA = 25°C and represent most likely parametric norm.

(2)

Limits are guaranteed to TI's AOQL (Average Outgoing Quality Level).

(3)

The 1µA limit is based on a testing limitation and does not reflect the actual performance of the part. Expect to see a doubling of the

current for every 15°C increase in temperature. For example, the 1nA typical current at 25°C would increase to 16nA at 85°C.

(4)

Source currents are flowing out of the LM26LV/LM26LV-Q1. Sink currents are flowing into the LM26LV/LM26LV-Q1.

(5)

Line regulation (DC) is calculated by subtracting the output voltage at the highest supply voltage from the output voltage at the lowest

supply voltage. The typical DC line regulation specification does not include the output voltage shift discussed in Section 4.3.

Submit Documentation Feedback

Product Folder Links: LM26LV

LM26LVCISD-080/NOPB bảng dữ liệu(PDF) 7 Page - Texas Instruments

LM26LVCISD-080/NOPB bảng dữ liệu(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

bảng dữ liệu tải về

Link URL