ADC12DL065CIVSSLASHNOPB datasheet(7/35 Pages) TI1

7 / 35 page

ADC12DL065

www.ti.com

SNAS249D – MARCH 2005 – REVISED APRIL 2013

Converter Electrical Characteristics

Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR =

+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 65 MHz, fIN = 10 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On,

parallel output mode. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C

(1) (2) (3)

Units

Parameter

Test Conditions

Typical(4)

Limits(4)

(Limits)

STATIC CONVERTER CHARACTERISTICS

Resolution with No Missing Codes

Bits (min)

INL

Integral Non Linearity(5)

±0.75

±1.7

LSB (max)

DNL

Differential Non Linearity

±0.4

±1.0

LSB (max)

PGE

Positive Gain Error

±0.2

±2.9

%FS (max)

NGE

Negative Gain Error

±0.2

±3.2

%FS (max)

TC GE

Gain Error Tempco

−40°C ≤ TA ≤ +85°C

ppm/°C

%FS (max)

VOFF

Offset Error (VIN+ = VIN−)

0.18

±0.85

%FS (min)

TC VOFF

Offset Error Tempco

−40°C ≤ TA ≤ +85°C

3.6

ppm/°C

Under Range Output Code

Over Range Output Code

4095

REFERENCE AND ANALOG INPUT CHARACTERISTICS

0.5

V (min)

VCM

Common Mode Input Voltage

1.5

2.0

V (max)

VRMA,

Reference Output Voltage

Output load = 1 mA

1.5

VRMB

(CLK LOW)

CIN

VIN Input Capacitance (each pin to GND)

VIN = 2.5 Vdc + 0.7 Vrms

(CLK HIGH)

0.8

V (min)

VREF

External Reference Voltage(6)

1.00

1.2

V (max)

Reference Input Resistance

Ω (min)

(1)

The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided

current is limited per Note 4 of the Absolute Maximum Ratings Table. However, errors in the A/D conversion can occur if the input goes

above VA or below GND by more than 100 mV. As an example, if VA is +3.3V, the full-scale input voltage must be ≤+3.4V to ensure

accurate conversions. See Figure 2.

(2)

To ensure accuracy, it is required that |VA–VD| ≤ 100 mV and separate bypass capacitors are used at each power supply pin.

(3)

With the test condition for VREF = +1.0V (2VP-P differential input), the 12-bit LSB is 488 µV.

(4)

Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are ensured to TI's AOQL (Average Outgoing

Quality Level).

(5)

Integral Non Linearity is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through

positive and negative full-scale.

(6)

Optimum performance will be obtained by keeping the reference input in the 0.8V to 1.2V range. The LM4051CIM3-ADJ (SOT-23

package) is recommended for external reference applications.

Submit Documentation Feedback

Product Folder Links: ADC12DL065

ADC12DL065CIVS/NOPB bảng dữ liệu(PDF) 7 Page - Texas Instruments

ADC12DL065CIVS/NOPB bảng dữ liệu(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

bảng dữ liệu tải về

Link URL