F303RE datasheet(21/65 Pages) ETC2

21 / 65 page

DocID025833 Rev 9

17/61

UM1724

Hardware layout and configuration

5.3.3

External power supply input: + 3V3

It can be of interest to use the +3V3 (CN6 pin 4 or CN7 pin 12 and pin 16) directly as power

input for instance in case the 3.3 V is provided by an extension board. When NUCLEO is

power supplied by +3V3, the ST-LINK is not powered thus the programming and debug

features are unavailable. The external power sources +3.3V is summarized in the Table 8.

Two different configurations are possible to use +3V3 to power the board:

•

ST-LINK is removed (PCB cut), or

•

SB2 (3V3 regulator) & SB12 (NRST) are OFF.

5.3.4

External power supply output

When powered by USB, VIN or E5V, the +5V (CN6 pin 5 or CN7 pin 18) can be used as

output power supply for an Arduino shield or an extension board. In this case, the maximum

current of the power source specified in Table 6 needs to be respected.

The +3.3 V (CN6 pin 4 or CN7 pin 12 & 16) can be used also as power supply output. The

current is limited by the maximum current capability of the regulator U4 (500 mA max).

5.4

LEDs

The tricolor LED (green, orange, red) LD1 (COM) provides information about ST-LINK

communication status. LD1 default color is red. LD1 turns to green to indicate that

communication is in progress between the PC and the ST-LINK/V2-1, with the following

setup:

•

Slow blinking Red/Off: at power-on before USB initialization

•

Fast blinking Red/Off: after the first correct communication between the PC and ST-

LINK/V2-1 (enumeration)

•

Red LED On: when the initialization between the PC and ST-LINK/V2-1 is complete

•

Green LED On: after a successful target communication initialization

•

Blinking Red/Green: during communication with target

•

Green On: communication finished and successful.

•

Orange On: Communication failure

User LD2: the green LED is a user LED connected to Arduino signal D13 corresponding to

MCU I/O PA5 (pin 21) or PB13 (pin 34) depending on the STM32 target. Please refer to

Table 10 to Table 21.

•

When the I/O is HIGH value, the LED is on.

•

When the I/O is LOW, the LED is off.

LD3 PWR: the red LED indicates that the MCU part is powered and +5V power is available.

Table 8. +3.3V eternal power source

Input power

name

Connectors pins

Voltage range

Limitation

+3V3

CN6 pin 4

CN7 pin 12 and pin 16

3 V to 3.6 V

Used when ST-LINK part of PCB is cut or

SB2 and SB12 OFF

F303RE bảng dữ liệu(PDF) 21 Page - List of Unclassifed Manufacturers

F303RE bảng dữ liệu(HTML) 21 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

bảng dữ liệu tải về

Link URL