TAS5760MDAPR datasheet(13/84 Pages) TI1

13 / 84 page

TAS5760M

www.ti.com

SLOS772D – JULY 2013 – REVISED JULY 2015

Speaker Amplifier in Mono Parallel Bridge Tied Load (PBTL) Mode (continued)

input signal is 1 kHz Sine, specifications are over operating free-air temperature range (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

PVDD = 12 V, SPK_GAIN[1:0] Pins = 00,

RSPK = 2Ω, THD+N = 0.1%,

PVDD = 12 V, SPK_GAIN[1:0] Pins = 00,

15.9

RSPK = 4Ω, THD+N = 0.1%,

PVDD = 12 V, SPK_GAIN[1:0] Pins = 00,

8.4

RSPK = 8Ω, THD+N = 0.1%

PVDD = 15 V, SPK_GAIN[1:0] Pins = 01,

28.5

RSPK = 2Ω, THD+N = 0.1%,

PVDD = 15 V, SPK_GAIN[1:0] Pins = 01,

RSPK = 4Ω, THD+N = 0.1%,

PVDD = 15 V, SPK_GAIN[1:0] Pins = 01,

13.3

RSPK = 8Ω, THD+N = 0.1%

Maximum Continuous Output

PO(SPK)

Power(1)

PVDD = 19 V, SPK_GAIN[1:0] Pins = 01,

26.5

RSPK = 2Ω, THD+N = 0.1%,

PVDD = 19 V, SPK_GAIN[1:0] Pins = 01,

RSPK = 4Ω, THD+N = 0.1%,

PVDD = 19 V, SPK_GAIN[1:0] Pins = 01,

21.3

RSPK = 8Ω, THD+N = 0.1%

PVDD = 24 V, SPK_GAIN[1:0] Pins = 10,

RSPK = 2Ω, THD+N = 0.1%,

PVDD = 24 V, SPK_GAIN[1:0] Pins = 10,

RSPK = 4Ω, THD+N = 0.1%,

PVDD = 24 V, SPK_GAIN[1:0] Pins = 10,

34.1

RSPK = 8Ω, THD+N = 0.1%

PVDD = 12 V, SPK_GAIN[1:0] Pins = 00,

100.4

RSPK = 8Ω, A-Weighted, -60dBFS Input

PVDD = 15 V, SPK_GAIN[1:0] Pins = 01,

99.5

RSPK = 8Ω, A-Weighted, -60dBFS Input

Signal to Noise Ratio (Referenced

SNR

to THD+N = 1%)

PVDD = 19 V, SPK_GAIN[1:0] Pins = 01,

100.1

RSPK = 8Ω, A-Weighted, -60dBFS Input

PVDD = 24 V, SPK_GAIN[1:0] Pins = 10,

99.5

RSPK = 8Ω, A-Weighted, -60dBFS Input

(1)

The continuous power output of any amplifier is determined by the thermal performance of the amplifier as well as limitations placed on

it by the system around it, such as the PCB configuration and the ambient operating temperature. The performance characteristics listed

in this section are achievable on the TAS5760M's EVM, which is representative of the poplular "2 Layers / 1oz Copper" PCB

configuration in a size that is representative of the amount of area often provided to the amplifier section of popular consumer audio

electronics. As can be seen in the instantaneous power portion of this table, more power can be delivered from the TAS5760M if steps

are taken to pull more heat out of the device. For instance, using a board with more layers or adding a small heatsink will result in an

increase of continuous power, up to and including the instantaneous power level. This behavior can also been seen in the POUT vs.

PVDD plots shown in the Typical Characteristics (Mono PBTL Mode): fSPK_AMP = 384 kHz section of this data sheet.

Submit Documentation Feedback

Product Folder Links: TAS5760M

TAS5760MDAPR bảng dữ liệu(PDF) 13 Page - Texas Instruments

TAS5760MDAPR bảng dữ liệu(HTML) 13 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

bảng dữ liệu tải về

Link URL