5

FN6494.0

April 25, 2008

LGATE Rise Time (Note 4)

t_RL

VCC = 5V, 3nF load, 10% to 90%

8

ns

UGATE Fall Time (Note 4)

t_FU

VCC = 5V, 3nF load, 10% to 90%

8

ns

LGATE Fall Time (Note 4)

t_FL

VCC = 5V, 3nF load, 10% to 90%

4

ns

UGATE Turn-On Propagation Delay (Note 4)

t_PDHU

VCC = 5V, 3nF load, adaptive

40

ns

LGATE Turn-On Propagation Delay (Note 4)

t_PDHL

VCC = 5V, 3nF load, adaptive

23

ns

UGATE Turn-Off Propagation Delay (Note 4)

t_PDLU

VCC = 5V, 3nF load

18

ns

LGATE Turn-Off Propagation Delay (Note 4)

t_PDLL

VCC = 5V, 3nF load

25

ns

Minimum Lgate on time at Diode emulation

t_LG_ON_DM

VCC = 5V

230

330

450

ns

OUTPUT (Note 4)

Upper Drive Source Current

I_U_Source

VCC = 5V, 3nF load

2

A

Upper Drive Source Impedance

R_U_SOURCE 20mA source current

1

Ω

Upper Drive Sink Current

I_U_SINK

VCC = 5V, 3nF load

2

A

Upper Drive Sink Impedance

R_U_SINK

20mA sink current

1

Ω

Lower Drive Source Current

I_L_SOURCE

VCC = 5V, 3nF load

2

A

Lower Drive Source Impedance

R_L_SOURCE 20mA source current

1

Ω

Lower Drive Sink Current

I_L_SINK

VCC = 5V, 3nF load

4

A

Lower Drive Sink Impedance

R_L_SINK

20mA sink current

0.4

Ω

NOTE:

4. Limits should be considered typical and are not production tested.

Electrical Specifications

Recommended Operating Conditions; Parameters with MIN and/or MAX limits are 100% tested at +25°C,

unless otherwise specified. Temperature limits established by characterization and are not production

tested. (Continued)

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

TYP

MAX

UNITS

Functional Pin Description

PACKAGE PIN #

PIN

SYMBOL

FUNCTION

SOIC

DFN

1

1

UGATE

Upper gate drive output. Connect to gate of high-side power N-Channel MOSFET.

2

2

BOOT

Floating bootstrap supply pin for the upper gate drive. Connect the bootstrap capacitor between this pin and the

PHASE pin. The bootstrap capacitor provides the charge to turn on the upper MOSFET. See “Internal Bootstrap

Device” on page 7 for guidance in choosing the capacitor value.

-

3, 8

NC

No connect.

3

4

PWM

The PWM signal is the control input for the driver. The PWM signal can enter three distinct states during operation.

See “Advanced PWM Protocol (Patent Pending)” on page 6 for further details. Connect this pin to the PWM output

of the controller.

4

5

GND

Bias and reference ground. All signals are referenced to this node. It is also the power-ground return of the driver.

5

6

LGATE

Lower gate drive output. Connect to gate of the low-side power N-Channel MOSFET.

6

7

VCC

Connect this pin to 5V bias supply. This pin supplies power to the upper gate and lower gate drive. Place a high

quality low ESR ceramic capacitor from this pin to GND.

7

9

EN

Enable input pin. Connect this pin high to enable driver and low to disable driver.

8

10

PHASE

Connect this pin to the SOURCE of the upper MOSFET and the DRAIN of the lower MOSFET. This pin provides

a return path for the upper gate drive.

-

11

PAD

Connect this pad to the power ground plane (GND) via thermally enhanced connection.

ISL6620, ISL6620A