| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LTC1735IGN-1 bảng dữ liệu(PDF) 14 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1735IGN-1 bảng dữ liệu(HTML) 14 Page - Linear Technology |
|
14 / 28 page ![]() 14 LTC1735-1 APPLICATIO S I FOR ATIO Manufacturers such as Nichicon, United Chemicon and Sanyo can be considered for high performance through- hole capacitors. The OS-CON semiconductor dielectric capacitor available from Sanyo has the lowest (ESR)(size) product of any aluminum electrolytic at a somewhat higher price. An additional ceramic capacitor in parallel with OS-CON capacitors is recommended to reduce the inductance effects. In surface mount applications, multiple capacitors may need to be used in parallel to meet the ESR, RMS current handling and load step requirements of the application. Aluminum electrolytic, dry tantalum and special polymer capacitors are available in surface mount packages. Special polymer surface mount capacitors offer very low ESR but have much lower capacitive density per unit volume than other capacitor types. These capacitors offer a very cost- effective output capacitor solution and are an ideal choice when combined with a controller having high loop bandwidth. Tantalum capacitors offer the highest capacitance density and are often used as output capacitors for switching regulators having controlled soft-start. Several excellent surge-tested choices are the AVX TPS, AVX TPSV or the KEMET T510 series of surface mount tantalums, available in case heights ranging from 2mm to 4mm. Aluminum electrolytic capacitors can be used in cost-driven applications providing that consideration is given to ripple current ratings, temperature and long-term reliability. A typical application will require several to many aluminum electrolytic capacitors in parallel. A combination of the above mentioned capacitors will often result in maximizing performance and minimizing overall cost. Other capacitor types include Sanyo OS-CON, Nichicon PL series and Sprague 595D series. Consult manufacturers for other specific recommendations. INTVCC Regulator An internal P-channel low dropout regulator produces the 5.2V supply that powers the drivers and internal circuitry within the LTC1735-1. The INTVCC pin can supply a maximum RMS current of 50mA and must be bypassed to ground with a minimum of 4.7 µF tantalum, 10µF special polymer or low ESR type electrolytic capacitor. A 1 µF ceramic capacitor placed directly adjacent to the INTVCC and PGND IC pins is highly recommended. Good bypassing is required to supply the high transient cur- rents required by the MOSFET gate drivers. Higher input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maxi- mum junction temperature rating for the LTC1735-1 to be exceeded. The system supply current is normally domi- nated by the gate charge current. Additional loading of INTVCC also needs to be taken into account for the power dissipation calculations. The total INTVCC current can be supplied by either the 5.2V internal linear regulator or by the EXTVCC input pin. When the voltage applied to the EXTVCC pin is less than 4.7V, all of the INTVCC current is supplied by the internal 5.2V linear regulator. Power dissipation for the IC in this case is highest, (VIN)(IINTVCC), and overall efficiency is lowered. The gate charge current is dependant on operating frequency as discussed in the Efficiency Consideration section. The junction tempera- ture can be estimated by using the equations given in Note 2 of the Electrical Characteristics. For example, the LTC1735CS-1 is limited to less than 17mA from a 30V supply when not using the EXTVCC pin as follows: TJ = 70°C + (17mA)(30V)(110°C/W) = 126°C Use of the EXTVCC input pin reduces the junction tempera- ture to: TJ = 70°C + (17mA)(5V)(110°C/W) = 79°C To prevent maximum junction temperature from being exceeded, the input supply current must be checked operating in continuous mode at maximum VIN. EXTVCC Connection The LTC1735-1 contains an internal P-channel MOSFET switch connected between the EXTVCC and INTVCC pins. Whenever the EXTVCC pin is above 4.7V the internal 5.2V regulator shuts off, the switch closes and INTVCC power is supplied via EXTVCC until EXTVCC drops below 4.5V. This allows the MOSFET gate drive and control power to be derived from the output or other external source during normal operation. When the output is out of regulation (start-up, short circuit) power is supplied from the internal regulator. Do not apply greater than 7V to the EXTVCC pin and ensure that EXTVCC < VIN. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |