| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LTC1735IGN-1 bảng dữ liệu(PDF) 10 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1735IGN-1 bảng dữ liệu(HTML) 10 Page - Linear Technology |
|
10 / 28 page ![]() 10 LTC1735-1 OPERATIO (Refer to Functional Diagram) POWER GOOD A window comparator monitors the output voltage and its open-drain output is pulled low when the divided down output voltage (appearing at the VOSENSE pin) is not within ±7.5% of the reference voltage of 0.8V. During a programmed output voltage transition (i.e., a transition from 1.55V to 1.3V) the PGOOD open-drain output will be pulled low and Burst Mode operation will be disabled until the output voltage is within 7.5% of its newly programmed value. When the PGOOD pin is driven by an external oscillator through a series resistor, cycle-skipping operation is invoked and the internal oscillator is synchronized to the external clock by comparator C. In this mode, the 25% minimum inductor current clamp is removed, providing low noise, constant frequency discontinuous operation over the widest possible output current range. This con- stant frequency operation is not quite as efficient as Burst Mode operation, but does provide a lower noise, constant frequency operation. When the power good window com- parator indicates the output is not in regulation, the PGOOD pin is pulled to ground and synchronization is inhibited. Obviously when driving the PGOOD pin with an external clock the power good indication is not available unless additional circuitry is added. If the PGOOD pin is tied to ground, continuous operation is forced. This operation is the least efficient mode, but is desirable in certain applications. The output can source or sink current in this mode. When forcing continuous operation and sinking current, current will be forced back into the main power supply potentially boosting the input supply to dangerous voltage levels—BEWARE. APPLICATIO S I FOR ATIO The basic LTC1735-1 application circuit is shown in Figure 1 on the first page of this data sheet. External component selection is driven by the load requirement and begins with the selection of RSENSE. Once RSENSE is known, COSC and L can be chosen. Next, the power MOSFETs and D1 are selected. The operating frequency and the inductor are chosen based largely on the desired amount of ripple current. Finally, CIN is selected for its ability to handle the large RMS current into the converter and COUT is chosen with low enough ESR to meet the output voltage ripple and transient specifications. The circuit shown in Figure 1 can be configured for operation up to an input voltage of 28V (limited by the external MOSFETs). RSENSE Selection For Output Current RSENSE is chosen based on the required output current. The LTC1735-1 current comparator has a maximum threshold of 75mV/RSENSE and an input common mode range of SGND to 1.1(INTVCC). The current comparator threshold sets the peak of the inductor current, yielding a maximum average output current IMAX equal to the peak value less half the peak-to-peak ripple current, ∆IL. Allowing a margin for variations in the LTC1735-1 and external component values yields: R mV I SENSE MAX = 50 COSC Selection for Operating Frequency and Synchronization The choice of operating frequency and inductor value is a trade-off between efficiency and component size. Low frequency operation improves efficiency by reducing MOSFET switching losses, both gate charge loss and transition loss. However, lower frequency operation requires more inductance for a given amount of ripple current. The LTC1735-1 uses a constant frequency architecture with the frequency determined by an external oscillator capacitor COSC. Each time the topside MOSFET turns on, the voltage on COSC is reset to ground. During the on-time, COSC is charged by a fixed current. When the voltage on the capacitor reaches 1.19V, COSC is reset to ground. The process then repeats. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |