công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

Preview PDF HTML

AN2335 bảng dữ liệu(PDF) 18 Page - STMicroelectronics

tên linh kiện AN2335
Giải thích chi tiết về linh kiện  This document is intended to give application
PDF  40 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  STMICROELECTRONICS [STMicroelectronics]
Trang chủ  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

AN2335 bảng dữ liệu(HTML) 18 Page - STMicroelectronics

Back Button AN2335 Datasheet HTML 14Page - STMicroelectronics AN2335 Datasheet HTML 15Page - STMicroelectronics AN2335 Datasheet HTML 16Page - STMicroelectronics AN2335 Datasheet HTML 17Page - STMicroelectronics AN2335 Datasheet HTML 18Page - STMicroelectronics AN2335 Datasheet HTML 19Page - STMicroelectronics AN2335 Datasheet HTML 20Page - STMicroelectronics AN2335 Datasheet HTML 21Page - STMicroelectronics AN2335 Datasheet HTML 22Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 40 page
background image
About control registers
AN2335
18/40
6
About control registers
6.1
CTRL_REG1 (20h)
Control register #1.
DR bit allows to select the data rate at which acceleration samples are produced. The
default value is 0 which corresponds to a data-rate of 100Hz. By changing the content of DR
to 1 the selected data-rate will be set equal to 400Hz.
PD bit allows to turn the device out of power-down mode. The device is in power-down mode
when PD= “0” (default value after boot). The device is in normal mode when PD is set to 1.
STP, STM bits are used to activate the self test function. When one of the bit is set to 1, an
output change will occur to the device outputs (refer to datasheet for specification) thus
allowing to check the functionality of the whole measurement chain. STP and STM move the
output in opposite directions.
Zen bit enables the generation of DataReady signal for Z-axis measurement channel when
set to 1. The default value is 1.
Yen bit enables the generation of DataReady signal for Y-axis measurement channel when
set to 1. The default value is 1.
Xen bit enables the generation of DataReady signal for X-axis measurement channel when
set to 1. The default value is 1.
DR
PD
FS
ST P
ST M
Zen
Yen
Xen
DR
Data rate selection. Default value: 0
(0: 100 Hz output data rate; 1: 400 Hz output data rate)
PD
Power Down Control. Default value: 0
(0: power down mode; 1: active mode)
FS
Full Scale selection. Default value: 0
(0: +/- 2g; 1: +/- 8g)
STP, STM
Self Test Enable. Default value: 00
(00: normal mode; 10: self test P; 01 self test M; 11: forbidden)
Zen
Z axis enable. Default value: 1
(0: Z axis disabled; 1: Z axis enabled)
Yen
Y axis enable. Default value: 1
(0: Y axis disabled; 1: Y axis enabled)
Xen
X axis enable. Default value: 1
(0: X axis disabled; 1: X axis enabled)
DR (DataRate)
PD (PowerDown)
Status
0
0
Power Down (Default)
0
1
Active (100Hz output)
1
0
Power Down
1
1
Active (400Hz output)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com