| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AN1049 bảng dữ liệu(PDF) 19 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
AN1049 bảng dữ liệu(HTML) 19 Page - STMicroelectronics |
|
19 / 24 page ![]() obviously, DCM will take place for Pin < PinT and CCM for Pin > PinT. This equation can be rewritten as follows: PinT = VE 2 2 ⋅ ZE (A6) by defining the "Equivalent Input Voltage" (VE) and the "Equivalent Primary Impedance" (ZE): VE = Vin 1 + Vin VR ; ZE = fSW ⋅ Lp (A7). VE is a function of Vin only (see fig. A2), since the reflected voltage (VR) is fixed. The variation of VE in its range [VEmin , VEmax ], which depends on the mains voltage range, in turn defines the range of PinT [PinTmin ,PinTmax]. Fig. A3 shows the diagram of (A6) while Tab. A1 presents the ranges of VE relevant to typical mains voltage ranges, as well as the corresponding PinTmax / PinTmin ratios. To complete the characterization of the transition between DCM and CCM it is convenient to define the Transition Voltage (VET), that is the Equivalent Input Voltage at which the operation is on the boundary between DCM and CCM, for a given Pin and a given ZE: VET = √ 2 ⋅ ZE ⋅ Pin (A8). DCM will take place for VE > VET and CCM for VE < VET. In synchronized converters it is possible to define also the Transition Frequency (fT), that is the switch- ing frequency at which the operation is on the boundary between DCM and CCM, for a given VE and a given Pin: fT = VE 2 2 ⋅ Lp ⋅ Pin (A9). DCM will take place for fsw < fT and CCM for fsw > fT. The peak primary current at transition is then: Ippk(T) = √ 2 ⋅ PinT fSW ⋅ Lp = 1 fSW ⋅ Lp ⋅ Vin 1 + Vin VR = VE ZE (A9). In case of CCM operation, equation (A4) still applies but the timing relationships (A2) change as follows: TON = Lp ⋅ ∆Ip Vin ; TFW = T − TON = Lp ⋅ ∆Ip VR (A10), where ∆Ip is the primary current ripple. n • Vout VE Vinmin Vinmax VEmax VEmin Vin Figure A2. Equivalent Input Voltage vs. DC Input Voltage VE PinT VEmin VEmax Pin VET fsw Figure A3. Characterization of the transi- tion DCM ⇐⇒ CCM AN1049 APPLICATION NOTE 19/24 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |