công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

ICL7149CPL bảng dữ liệu(PDF) 3 Page - Intersil Corporation

tên linh kiện ICL7149CPL
Giải thích chi tiết về linh kiện  33/4 Digit, Autoranging Multimeter
PDF  13 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  INTERSIL [Intersil Corporation]
Trang chủ  http://www.intersil.com/cda/home
Logo INTERSIL - Intersil Corporation

ICL7149CPL bảng dữ liệu(HTML) 3 Page - Intersil Corporation

  ICL7149CPL Datasheet HTML 1Page - Intersil Corporation ICL7149CPL Datasheet HTML 2Page - Intersil Corporation ICL7149CPL Datasheet HTML 3Page - Intersil Corporation ICL7149CPL Datasheet HTML 4Page - Intersil Corporation ICL7149CPL Datasheet HTML 5Page - Intersil Corporation ICL7149CPL Datasheet HTML 6Page - Intersil Corporation ICL7149CPL Datasheet HTML 7Page - Intersil Corporation ICL7149CPL Datasheet HTML 8Page - Intersil Corporation ICL7149CPL Datasheet HTML 9Page - Intersil Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 3 / 13 page
background image
3-35
Absolute Maximum Ratings
Thermal Information
Supply Voltage (V+ to V-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Reference Input Voltage (VREF to COM) . . . . . . . . . . . . . . . . . . . 3V
Analog Input Current (IN + Current or IN + Voltage) . . . . . . . 100
µA
Clock Input Swing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V+ to V+ -3
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC
Thermal Resistance (Typical, Note 1)
θ
JA (
oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(MQFP - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1.
θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
V+ = 9V, TA = 25
oC, V
REF adjusted for -3.700 reading on DC volts, test circuit as shown in Figure 3.
Crystal = 120kHz. (See Figure 14)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Zero Input Reading
VIN or IIN or RIN = 0.00
-00.0
-
+00.0
V, I,
Ω
Linearity (Best Straight Line) (Note 6)
(Notes 1 and 8)
-1
-
+1
Counts
Accuracy DC V, 400V Range Only
(Notes 1 and 8)
-
-
±1
% of RDG
±1
Accuracy DC V, 400V Range Excluded
(Notes 1 and 8)
-
-
±0.30
% of RDG
±1
Accuracy
Ω, 4K and 400K Range
(Notes 1 and 8)
-
-
±0.75
% of RDG
±8
Accuracy
Ω, 4K and 4M Range
(Notes 1 and 8)
-
-
±1
% of RDG
±9
Accuracy DC I, Unadjusted for Full Scale
(Notes 1 and 8)
-
-
±0.75
% of RDG
±1
Accuracy DC I, Adjusted for Full Scale
(Notes 1 and 8)
-
±0.2
-
% of RDG
±1
Accuracy AC V
At 60Hz (Notes 5, 7, and 8)
-
±2
-
% of RDG
Open Circuit Voltage for
Ω Measurements
RUNKNOWN = Infinity
-
VREF
-V
Noise
VIN = 0, DC V (Note 2, 95% of Time)
-
0.1
-
LSB
Noise
VIN = 0, AC V (Note 2, 95% of Time)
-
4
-
LSB
Supply Current
VIN = 0, DC Voltage Range
-
1.5
2.4
mA
Analog Common (with Respect to V+)
ICOMMON < 10µA
2.7
2.9
3.1
V
Temperature Coefficient of Analog Common
ICOMMON < 10µA, Temp. = 0
oC To 70oC
-
-100
-
ppm/oC
Output Impedance of Analog Common
ICOMMON < 10µA-
1
10
Ω
Backplane/Segment Drive Voltage
Average DC < 50mV
2.8
3.0
3.2
V
Backplane/Segment Display Frequency
-
75
-
Hz
Switch Input Current
VIN = V+ to V- (Note 3)
-50
-
+50
µA
Switch Input Levels (High Trip Point)
V+ - 0.5
-
V+
V
Switch Input Levels (Mid Trip Point)
V- + 3
-
V+ - 2.5
V
Switch Input Levels (Low Trip Point)
V-
-
V- + 0.5
V
Beeper Output Drive (Rise or Fall Time)
CLOAD = 10nF
-
25
100
µs
Beeper Output Frequency
-
2
-
kHz
Continuity Detect
Range = Low
Ω, VREF = 1.00V
-
1.5
-
k
Ω
Power Supply Functional Operation
V+ to V-
7
9
11
V
Low Battery Detect
V+ to V- (Note 4)
6.5
7
7.5
V
NOTES:
1. Accuracy is defined as the worst case deviation from ideal input value including: offset, linearity, and rollover error.
2. Noise is defined as the width of the uncertainty window (where the display will flicker) between two adjacent codes.
3. Applies to pins 17-20.
4. Analog Common falls out of regulation when the Low Battery Detect is asserted, however the ICL7139 and ICL7149 will continue to
operate correctly with a supply voltage above 7V and below 11V.
5. For 50Hz use a 100kHz crystal.
6. Guaranteed by design, not tested.
7. ICL7139 only.
8. RDG = Reading.
ICL7139, ICL7149



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com