HIP0081AS2 datasheet(4/15 Pages) INTERSIL

4 / 15 page

Absolute Maximum Ratings

Thermal Information

Supply Voltage (Logic and Control), VCC . . . . . . . . . . . . -16 to 45V

Power MOSFET Drain Voltage, VO (Note 1) . . . . . . -0.5 to VCLAMP

Maximum Output Clamp Energy, EOK (HIP0080) . . . . . . . . . Note 4

Maximum Output Clamp Energy, EOK (HIP0081) . . . . . . . . . Note 4

Input Voltage (Logic and Driver Inputs), VIN . . . . . . . . . . . -0.5 to 7V

Output Voltage, DATAOUT . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 7V

HIP0080 Output Current

Each Output, IOUT(PEAK), (Note 2) . . . . . . -1.5A to IOUT(SC)

Each Output, IOUT(DC) . . . . . . . . . . . . . . . . . . . . . . . . +1.3A

Total of 4 Outputs ON, Unequal IOUT . . . . . . . . . . . . . . . . +3A

Total of 4 Outputs ON, Unequal IOUT . . . . . +4A/500ms (Max)

HIP0081 Output Current

Each Output, IOUT(PEAK), (Note 2) . . . . . . . . . -2 to IOUT(SC)

Each Output, IOUT(DC) . . . . . . . . . . . . . . . . . . . . . . . . +2.2A

Total of 4 Outputs, ON, Unequal IOUT . . . . . . . . . . . . . . . +6A

Total of 4 Outputs ON, Unequal IOUT . . . . . +8A/500ms (Max)

Operating Conditions

Ambient Temperature Range . . . . . . . . . . . . . . . . . -40oC to 125oC

Junction Temperature Range . . . . . . . . . . . . . . . . . -40oC to 150oC

Thermal Resistance (Typical, Note 3)

θJA(oC/W) θJC(oC/W)

HIP0080 . . . . . . . . . . . . . . . . . . . . . . . .

N/A

HIP0080 (on 2 sq. in. PC Board) . . . . .

N/A

HIP0081 . . . . . . . . . . . . . . . . . . . . . . . .

HIP0080 Power Dissipation with a 2 sq. in. PC board heat sink:

At 85oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.95W

Above 85oC:. . . . . . . . . . . . . . . . . . . Derate Linearly at 30mW/oC

HIP0081 Power Dissipation with inﬁnite heat sink:

At 125oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.33W

Above 125oC . . . . . . . . . . . . . . . . . Derate Linearly at 333 mW/oC

Maximum Storage Temperature Range, TSTG . . . . -55

oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . 300oC

Die Characteristics

HIP0080 Back Side Potential . . . . . . . . . . . . . . Frame, GND Leads

HIP0081 Back Side Potential . . . . . . . . . Heat Sink Tab, GND Lead

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTES:

1. The MOSFET Output Drain is internally Clamped with a Drain-to-Gate zener diode that turns-on the MOSFET to hold the Drain at the VCLAMP

voltage. Refer to the Electrical Characteristic Tables for the VCLAMP voltage limits.

2. Each Output has Over-Current Shutdown protection in the positive current direction. The maximum peak current rating is determined by the

minimum Over-Current Shutdown as detailed in the Electrical Specification Table. In the event of an Over-Current Shutdown the input drive is

latched OFF. The output short must be removed and the input toggled OFF and ON to restore the output drive.

3. Effective Heat Sinking for the HIP0080 PLCC package requires a PC Board solder mount or equivalent. The HIP0080

θJA junction-to-air thermal

resistance is given for a PC Board with 2 sq. in. of 1 oz. surface mount ground copper extending away from the package. For additional Power

Dissipation Derating information, see Figure 8 curves.

4. Refer to Figures 4 and 5 Single Pulse Output Clamp Energy vs. Time Capability of the HIP0080 and HIP0081. The safe margin for single pulse

energy operation is below the dotted line shown in Figures 4 and 5.

Electrical Speciﬁcations VCC = 5.5V to 25V ±5%, TA = -40oC to 125oC, Unless Otherwise Speciﬁed

PARAMETER

SYMBOL

TEST CONDITIONS

HIP0080

HIP0081

UNITS

MIN

TYP

MAX

MIN

TYP

MAX

POWER OUTPUTS

Output ON Resistance

(HIP0081)

rON

VCC = 10 to 25V, All Outputs ON

IOUT1 = IOUT2 = IOUT3 = IOUT4 = 1A

---

0.5

Ω

VCC = 5.5 to 10V, All Outputs ON

IOUT1 = IOUT2 = IOUT3 = IOUT4 = 0.7A

---

1.0

Ω

Output ON Resistance

(HIP0080)

rON

VCC = 10 to 25V, All Outputs ON

IOUT1 = IOUT2 = IOUT3 = IOUT4 = 0.5A

1.0

Ω

VCC = 5.5 to 10V, All Outputs ON

IOUT1 = IOUT2 = IOUT3 = IOUT4 = 0.4A

2.0

Ω

HIP0081 Output Off Current

IOFF

Inputs Low, Each VOUT = 60V

TA = 25

oC to 125oC

0.75

1.0

Inputs Low, Each VOUT = 60V,

TA = -40

0.75

1.5

HIP0081 Output Leakage

Current

IOFFLK

Inputs Low, Each VOUT = 60V,

VCC = 0V

1.0

µA

HIP0080 Output Off

Current

IOFF

Inputs Low, Each VOUT = 25V,

ENABLE High, TA = 25

oC to 125oC

0.75

1.0

Inputs Low, Each VOUT = 25V,

ENABLE High, TA = -40

0.75

1.5

HIP0080, HIP0081

HIP0081AS2 bảng dữ liệu(PDF) 4 Page - Intersil Corporation

HIP0081AS2 bảng dữ liệu(HTML) 4 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

bảng dữ liệu tải về

Link URL