| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
HT49R50 bảng dữ liệu(PDF) 25 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT49R50 bảng dữ liệu(HTML) 25 Page - Holtek Semiconductor Inc |
|
25 / 59 page ![]() HT49R50 25 October 22, 1999 Q D CK S Q Da t a B u s Wr i t e C h i p R es et R e a d I/O S y s t em W ak e- up ( P A onl y ) W eak Pu l l - u p PA0 ~ PA7 PB0 ~ PB7 PC 0 ~ PC 3 Op t i o n V DD Op t i o n ( P A0~ P A3, PC ) V DD O p t i o n ( PA0 ~ PA3 , P C ) Input/output ports Input/output ports There are a 12-bit bidirectional input/output port, an 8-bit input port in the HT49R50, la- beled PA, PB and PC which are mapped to [12H], [14H] and [16H] of the RAM, respec- tively. PA0~PA3 can be configured as CMOS (output) or NMOS (input/output) with or without pull-high resistor by options. PA4~PA7 are always pull-high and NMOS (input/output). If you choose NMOS (input), each bit on the port (PA0~PA7) can be configured as a wake-up input. PB can only be used for input operation, and each bit on the port can be configured with pull-high resistor. PC can be configured as CMOS output or NMOS input/output with or without pull-high re- sistor by options. All the port for the input opera- tion (PA, PB and PC), these ports are non-latched, that is, the inputs should be ready at the T2 rising edge of the instruction MOV A, [m] (m=12H or 14H). For PA, PC output opera- tion, all data are latched and remain unchanged until the output latch is rewritten. When the PA and PC structures are open drain NMOS type, it should be noted that, before reading data from the pads, a 1 should be written to the related bits to disable the NMOS device. That is executing first the instruction "SET [m].i" (i=0~7 for PA) to disable related NMOS device, and then "MOV A, [m]" to get stable data. After chip reset, these input lines remain at the high level or are left floating (by options). Each bit of these output latches can be set or cleared by the "SET [m].i" and "CLR [m].i" (m=12H or 16H) instructions. Some instructions first input data and then fol- low the output operations. For example, "SET [m].i", "CLR [m].i", "CPL [m]", "CPLA [m]" read the entire port states into the CPU, execute the defined operations (bit-operation), and then write the results back to the latches or to the ac- cumulator. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |