ADC12DC080 datasheet(7/27 Pages) TI1

7 / 27 page

AGND

To Internal Circuitry

I/O

ADC12DC080

www.ti.com

SNAS405B – SEPTEMBER 2007 – REVISED NOVEMBER 2008

Dynamic Converter Electrical Characteristics

Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.0V, VDR = +2.5V, Internal VREF

= +1.2V, fCLK = 80 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25°C. Boldface limits apply for TMIN ≤ TA ≤

TMAX. All other limits apply for TA = 25°C

(1) (2)

Units

Typical

Symbol

Parameter

Conditions

Limits

(Limits)

(3)

(4)

DYNAMIC CONVERTER CHARACTERISTICS, AIN= -1dBFS

FPBW

Full Power Bandwidth

-1 dBFS Input,

−3 dB Corner

1.0

GHz

fIN = 10 MHz

71.5

dBFS

SNR

Signal-to-Noise Ratio

fIN = 70 MHz

70.5

dBFS

fIN = 170 MHz

69.5

68.6

dBFS

fIN = 10 MHz

dBFS

SFDR

Spurious Free Dynamic Range

fIN = 70 MHz

dBFS

fIN = 170 MHz

dBFS

fIN = 10 MHz

11.6

Bits

ENOB

Effective Number of Bits

fIN = 70 MHz

11.4

Bits

fIN = 170 MHz

11.2

Bits

fIN = 10 MHz

−86

dBFS

THD

Total Harmonic Disortion

fIN = 70 MHz

−85

dBFS

fIN = 170 MHz

−84

-77

dBFS

fIN = 10 MHz

−95

dBFS

Second Harmonic Distortion

fIN = 70 MHz

−90

dBFS

fIN = 170 MHz

−83

-78

dBFS

fIN = 10 MHz

−88

dBFS

Third Harmonic Distortion

fIN = 70 MHz

−85

dBFS

fIN = 170 MHz

−83

-78

dBFS

fIN = 10 MHz

71.3

dBFS

SINAD

Signal-to-Noise and Distortion Ratio

fIN = 70 MHz

70.3

dBFS

fIN = 170 MHz

69.3

dBFS

IMD

Intermodulation Distortion

fIN = 20 MHz and 21 MHz, each -7dBFS

-84

dBFS

0 MHz tested channel, fIN = 10 MHz at -

Crosstalk

-100

dBFS

1dBFS other channel

(1)

The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided

current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above

2.6V or below GND as described in the Operating Ratings section.

(2)

With a full scale differential input of 2VP-P , the 12-bit LSB is 488 µV.

(3)

Typical figures are at TA = 25°C and represent most likely parametric norms at the time of product characterization. The typical

specifications are not ensured.

(4)

This parameter is specified in units of dBFS - indicating the value that would be attained with a full-scale input signal.

Submit Documentation Feedback

Product Folder Links: ADC12DC080

ADC12DC080 bảng dữ liệu(PDF) 7 Page - Texas Instruments

ADC12DC080 bảng dữ liệu(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

bảng dữ liệu tải về

Link URL