LM6172AMGWFQMLV datasheet(5/25 Pages) NSC

5 / 25 page

LM6172QML

www.ti.com

SNOSAR4A – DECEMBER 2010 – REVISED OCTOBER 2011

LM6172 (±5V) ELECTRICAL CHARACTERISTICS

(1)

DC PARAMETERS (continued)

The following conditions apply, unless otherwise specified.

TJ = 25°C, V

+ = +5V, V− = −5V, V

CM = 0V & RL > 1MΩ

Sub-

Symbol

Parameter

Conditions

Notes

Min

Max

Units

groups

See (3)

Sourcing RL = 100Ω

See(3)

2, 3

Output Current (Open Loop)

See (3)

-24

Sinking RL = 100Ω

See (3)

-23

2, 3

6.0

Supply Current

Both Amplifiers

7.0

2, 3

(3)

The open loop output current is specified by measurement of the open loop output voltage swing using 100

Ω output load.

DC DRIFT PARAMETERS

(1)

The following conditions apply, unless otherwise specified.

TJ = 25°C, V

+ = +5V, V− = −5V, V

CM = 0V & RL > 1MΩ

Delta calculations performed on QMLV devices at group B , subgroup 5.

Sub-

Symbol

Parameter

Conditions

Notes

Min

Max

Units

groups

VIO

Input Offset Voltage

-0.25

0.25

IIB

Input Bias Current

-0.50

0.50

µA

IIO

Input Ofset Current

-0.25

0.25

µA

(1)

Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate

sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters

are specified only for the conditions as specified in Mil-Std-883, Method 1019.5, Condition A.

LM6172 (±15V) ELECTRICAL CHARACTERISTICS

DC PARAMETERS

(1)

The following conditions apply, unless otherwise specified.

TJ = 25°C, V

+ = +15V, V− = −15V, V

CM = 0V, & RL = 1MΩ

Sub-

Symbol

Parameter

Conditions

Notes

Min

Max

Units

groups

1.5

VIO

Input Offset Voltage

3.5

2, 3

3.0

µA

IIB

Input Bias Current

4.0

µA

2, 3

2.0

µA

IIO

Input Offset Current

3.0

µA

2, 3

CMRR

Common Mode Rejection Ratio

VCM = ±10V

2, 3

PSRR

Power Supply Rejection Ratio

VS = ±15V to ±5V

2, 3

See (2)

RL = 1KΩ

See (2)

2, 3

Large Signal Voltage Gain

See (2)

RL = 100Ω

See (2)

2, 3

(1)

Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate

sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters

are specified only for the conditions as specified in Mil-Std-883, Method 1019.5, Condition A.

(2)

Large signal voltage gain is the total output swing divided by the input signal required to produce that swing. For VS = ±15V, VOUT =

±5V. For VS = ±5V, VOUT = ±1V.

Submit Documentation Feedback

Product Folder Links: LM6172QML

LM6172AMGWFQMLV bảng dữ liệu(PDF) 5 Page - National Semiconductor (TI)

LM6172AMGWFQMLV bảng dữ liệu(HTML) 5 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

bảng dữ liệu tải về

Link URL