AD7682BCPZ datasheet(29/32 Pages) AD

29 / 32 page

Data Sheet

AD7682/AD7689

Rev. D | Page 29 of 32

READ/WRITE SPANNING CONVERSION WITHOUT

A BUSY INDICATOR

This mode is used when the AD7682/AD7689 are connected

to any host using an SPI, serial port, or FPGA. The connection

diagram is shown in Figure 40, and the corresponding timing

is given in Figure 41. For the SPI, the host should use CPHA =

CPOL = 0. Reading/writing spanning conversion is shown,

which covers all three modes detailed in the Digital Interface

section. For this mode, the host must generate the data transfer

based on the conversion time. For an interrupt driven transfer

that uses a busy indicator, refer to the Read/Write Spanning

Conversion with a Busy Indicator section.

A rising edge on CNV initiates a conversion, forces SDO to

high impedance, and ignores data present on DIN. After a

conversion is initiated, it continues until completion irrespec-

tive of the state of CNV. CNV must be returned high before the

safe data transfer time, tDATA, and then held high beyond the

conversion time, tCONV, to avoid generation of the busy signal

indicator.

After the conversion is complete, the AD7682/AD7689 enter

the acquisition phase and power-down. When the host brings

CNV low after tCONV (maximum), the MSB is enabled on SDO.

The host also must enable the MSB of the CFG register at this

time (if necessary) to begin the CFG update. While CNV is low,

both a CFG update and a data readback take place. The first 14

SCK rising edges are used to update the CFG, and the first 15

SCK falling edges clock out the conversion results starting with

MSB − 1. The restriction for both configuring and reading is

that they both must occur before the tDATA time of the next conver-

sion elapses. All 14 bits of CFG[13:0] must be written, or they

are ignored. In addition, if the 16-bit conversion result is not

read back before tDATA elapses, it is lost.

The SDO data is valid on both SCK edges. Although the rising

edge can be used to capture the data, a digital host using the

SCK falling edge allows a faster reading rate, provided it has an

acceptable hold time. After the 16th (or 30th) SCK falling edge, or

when CNV goes high (whichever occurs first), SDO returns to

high impedance.

If CFG readback is enabled, the CFG register associated with the

conversion result is read back MSB first following the LSB of the

conversion result. A total of 30 SCK falling edges is required to

return SDO to high impedance if this is enabled.

MISO

MOSI

SCK

CNV

FOR SPI USE CPHA = 0, CPOL = 0.

SCK

SDO

DIN

AD7682/

AD7689

DIGITAL HOST

Figure 40. Connection Diagram for the AD7682/AD7689 Without a Busy Indicator

UPDATE (n)

CFG/SDO

UPDATE (n + 1)

CFG/SDO

ACQUISITION (n)

ACQUISITION

(n + 1)

ACQUISITION

(n - 1)

MSB MSB – 1

BEGIN DATA (n – 1)

BEGIN CFG (n + 1)

CFG

MSB

CFG

MSB – 1

LSB + 1

SEE NOTE

NOTES

1. THE LSB IS FOR CONVERSION RESULTS OR THE CONFIGURATION REGISTER CFG (n – 1) IF

15 SCK FALLING EDGES = LSB OF CONVERSION RESULTS.

29 SCK FALLING EDGES = LSB OF CONFIGURATION REGISTER.

ON THE 16TH OR 30TH SCK FALLING EDGE, SDO IS DRIVEN TO HIGH IMPENDANCE.

16/

CONVERSION (n)

END DATA (n – 1)

END CFG (n + 1)

CFG

LSB

tCONV

LSB

SCK

CNV

DIN

SDO

LSB + 1

16/

CONVERSION (n – 1)

END DATA (n – 2)

END CFG (n)

CFG

LSB

tCONV

tDATA

tCNVH

tDATA

tDIS

tEN

tDSDO

tHSDO

tHDIN

tSDIN

tCLSCK

tEN

tSCK

tSCKH

tSCKL

tDIS

tCONV

LSB

tACQ

tCYC

(QUIET

TIME)

(QUIET

TIME)

EOC

RETURN CNV HIGH

FOR NO BUSY

RETURN CNV HIGH

FOR NO BUSY

Figure 41. Serial Interface Timing for the AD7682/AD7689 Without a Busy Indicator

AD7682BCPZ bảng dữ liệu(PDF) 29 Page - Analog Devices

AD7682BCPZ bảng dữ liệu(HTML) 29 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

bảng dữ liệu tải về

Link URL