AD7682BCPZ datasheet(16/32 Pages) AD

16 / 32 page

AD7682/AD7689

Data Sheet

Rev. D | Page 16 of 32

THEORY OF OPERATION

SW+

MSB

16,384C

INx+

LSB

COMP

CONTROL

LOGIC

SWITCHES CONTROL

BUSY

OUTPUT CODE

CNV

REF

GND

INx– OR

COM

32,768C

SW–

MSB

16,384C

LSB

32,768C

Figure 24. ADC Simplified Schematic

OVERVIEW

The AD7682/AD7689 are 4-channel/8-channel, 16-bit, charge

redistribution successive approximation register (SAR) analog-

to-digital converters (ADCs). These devices are capable of

converting 250,000 samples per second (250 kSPS) and power

down between conversions. For example, when operating with

an external reference at 1 kSPS, they consume 17 μW typically,

ideal for battery-powered applications.

The AD7682/AD7689 contain all of the components for use in a

multichannel, low power data acquisition system, including

•

16-bit SAR ADC with no missing codes

•

4-channel/8-channel, low crosstalk multiplexer

•

Internal low drift reference and buffer

•

Temperature sensor

•

Selectable one-pole filter

•

Channel sequencer

These components are configured through an SPI-compatible,

14-bit register. Conversion results, also SPI compatible, can be

read after or during conversions with the option for reading

back the configuration associated with the conversion.

The AD7682/AD7689 provide the user with an on-chip track-

and-hold and do not exhibit pipeline delay or latency.

The AD7682/AD7689 are specified from 2.3 V to 5.5 V and can

be interfaced to any 1.8 V to 5 V digital logic family. They are

housed in a 20-lead, 4 mm × 4 mm LFCSP that combines space

savings and allows flexible configurations. They are pin-for-pin

compatible with the 16-bit AD7699 and 14-bit AD7949.

CONVERTER OPERATION

The AD7682/AD7689 are successive approximation ADCs

based on a charge redistribution DAC. Figure 24 shows the

simplified schematic of the ADC. The capacitive DAC consists

of two identical arrays of 16 binary-weighted capacitors, which

are connected to the two comparator inputs.

During the acquisition phase, terminals of the array tied to the

comparator input are connected to GND via SW+ and SW−. All

independent switches are connected to the analog inputs.

Thus, the capacitor arrays are used as sampling capacitors and

acquire the analog signal on the INx+ and INx− (or COM)

inputs. When the acquisition phase is complete and the CNV

input goes high, a conversion phase is initiated. When the

conversion phase begins, SW+ and SW− are opened first. The

two capacitor arrays are then disconnected from the inputs and

connected to the GND input. Therefore, the differential voltage

between the INx+ and INx− (or COM) inputs captured at the

end of the acquisition phase is applied to the comparator inputs,

causing the comparator to become unbalanced. By switching

each element of the capacitor array between GND and REF, the

comparator input varies by binary-weighted voltage steps

(VREF/2, VREF/4, ... VREF/32,768). The control logic toggles these

switches, starting with the MSB, to bring the comparator back

into a balanced condition. After the completion of this process,

the part returns to the acquisition phase, and the control logic

generates the ADC output code and a busy signal indicator.

Because the AD7682/AD7689 have an on-board conversion

clock, the serial clock, SCK, is not required for the conversion

process.

AD7682BCPZ bảng dữ liệu(PDF) 16 Page - Analog Devices

AD7682BCPZ bảng dữ liệu(HTML) 16 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

bảng dữ liệu tải về

Link URL