| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
EVALAD5933EB bảng dữ liệu(PDF) 18 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
EVALAD5933EB bảng dữ liệu(HTML) 18 Page - Analog Devices |
|
18 / 32 page ![]() EVAL-AD5933EB Preliminary Technical Data Rev. PrC | Page 18 of 32 ‘The DDS is going to output 15 cycles of the output excitation voltage before the ADC will start sampling ‘the response signal. The settling time cycle multiplier is set to x1 SettlingTimebyte0 = 0F ‘15 cycles (decimal) = 0F hex SettlingTimebyte1 = 00 ’00 = X1 WritetToPart &H8B, SettlingTimebyte0 WritetToPart &H8A, SettlingTimebyte1 ‘-------------------------------------- PLACE AD5933 IN STANDBYMODE ---------------------------------------- ‘Standby mode command = B0 hex WritetToPart &H80, &HB0 '------------------------- Program the system clock and output excitation range and PGA setting----------- ‘Enable external Oscillator WritetToControlRegister2 &H81, &H8 ‘Set the output excitation range to be 2vp-p and the PGA setting to = x1 WritetToControlRegister2 &H80, &H1 ‘----------------------------------------------------------------------------------------------------------- ‘------------- ------------ Initialize impedance under test with start frequency --------------------------- 'Initialize Sensor with Start Frequency WritetToControlRegister &H80, &H10 msDelay 2 'this is a user determined delay dependant upon the network under analysis (2ms delay) ‘-------------------------------------- Start the frequency sweep ------------------------------------------ 'Start Frequency Sweep WritetToControlRegister &H80, &H20 'Enter Frequency Sweep Loop ReadbackStatusRegister = PortRead(&HD, &H8F) ReadbackStatusRegister = ReadbackStatusRegister And &H4 ' mask off bit D2 (i.e. is the sweep complete) Do While ((ReadbackStatusRegister <> 4) And (Increment <> 0)) 'check to see if current sweep point complete ReadbackStatusRegister = PortRead(&HD, &H8F) ReadbackStatusRegister = ReadbackStatusRegister And &H2 'mask off bit D1 (valid real and imaginary data available) ‘------------------------------------------------------------------------- If (ReadbackStatusRegister = 2) Then ' this sweep point has returned valid data so we can proceed with sweep Else Do ‘if valid data has not been returned then we need to pole stat reg until such time as valid data 'has been returned ‘i.e. if point is not complete then Repeat sweep point and pole staus reg until valid data returned WritetToControlRegister &H80, &H40 'repeat sweep point Do ReadbackStatusRegister = PortRead(&HD, &H8F) ReadbackStatusRegister = ReadbackStatusRegister And &H2 ' mask off bit D1- Wait until dft complete Loop While (ReadbackStatusRegister <> 2) Loop Until (ReadbackStatusRegister = 2) End If '------------------------------------------------------------------------- RealDataUpper = PortRead(&HD, &H94) RealDataLower = PortRead(&HD, &H95) RealData = RealDataLower + (RealDataUpper * 256) 'The Real data is stored in a 16 bit 2's complement format. 'In order to use this data it must be converted from 2's complement to decimal format If RealData <= &H7FFF Then ' h7fff 32767 ' Positive Else ' Negative ' RealData = RealData And &H7FFF |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |