| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
EM3027IDSWS8 bảng dữ liệu(PDF) 20 Page - EM Microelectronic - MARIN SA |
|
|
|||||||||||||||||||||||||||||
EM3027IDSWS8 bảng dữ liệu(HTML) 20 Page - EM Microelectronic - MARIN SA |
|
20 / 28 page ![]() EM3027 Copyright 2013, EM Microelectronic-Marin SA 3027-DS.doc, Version 8.0, 25-Jan-13 20 www.emmicroelectronic.com 9 Power Management I/O Switchover Logic, EEPROM, Thermometer, Voltage Monitor Regulator 2.9V Xtal Oscillator 4x Trickle charger resistors VCC VBack VReg VHigh Figure 6: Power Management 9.1 Power Supplies, Switchover and Trickle Charger The device can be supplied from the VCC pin or from the VBack pin. The switchover block implemented inside the chip compares VCC and VBack voltages and connects the higher of them to the internal VHigh net that supplies the chip. Nevertheless, the communication pins (SCL, SDA or CS, SCK, SI, SO) are supplied from the VCC pin. For that reason, when serial interface (I2C or SPI) is used, the chip has to be supplied from VCC. (i.e. VCC > VBack). By setting of a trickle charger bit in register EEctrl, a resistor can be inserted between VBack and VHigh voltage. In this way, a rechargeable battery or a super-cap can be charged from the VCC voltage, as long as VCC > VBack. There are 4 selectable resistors connected in parallel with typical values of 80kΩ, 20kΩ, 5kΩ and 1.5kΩ. One or more resistors can be selected by EEctrl bits setting. If a Lithium battery shall be connected to VBack pin, a protection resistor of value up to 1k Ω can be connected in series with it. In this way, in case of EM3027 device damage resulting in short between both supply pins, charging current from the VCC supply can be reduced to its allowed maximum level as required by UL1642 standard. 5.5V 3.0V 4.0V 5.0V 2.0V 1.0V 0V Supply Voltage 2.2V 1.4V EM3027 fully operating according datasheet (clock, thermometer, thermocompensation) Clock operating with thermocompensation using either previously in fully operating mode measured or by user stored temperature value; no EEPROM write Serial communication is enabled, if VCC > VCCmin and VCC > Vback VCCmax Vprog EEPROM write if VCC > Vprog min max min max VCCmin Figure 7: EM3027 operating Voltage Areas |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |