PIC24FJ64GA108 datasheet(12/22 Pages) MICROCHIP

12 / 22 page

PIC24FJ256GA110 FAMILY

DS80368N-page 12

 2008-2013 Microchip Technology Inc.

Data Sheet Clarifications

The following typographic corrections and clarifications

are to be noted for the latest version of the device data

sheet (DS39905E):

1. Module: Guidelines for Getting Started

with 16-Bit Microcontrollers

Section 2.4 Voltage Regulator Pins (ENVREG/

DISVREG and VCAP/VDDCORE) has been replaced

with a new and more detailed section. The entire text

follows:

2.4

Voltage Regulator Pins Voltage

Regulator Pins

(ENVREG/DISVREG and

VCAP/VDDCORE)

The on-chip voltage regulator enable/disable pin

(ENVREG or DISVREG, depending on the device

family) must always be connected directly to either a

supply voltage or to ground. The particular connection

is determined by whether or not the regulator is to be

used:

• For ENVREG, tie to VDD to enable the regulator,

or to ground to disable the regulator

• For DISVREG, tie to ground to enable the



regulator or to VDD to disable the regulator

Refer to Section 25.2 “On-Chip Voltage Regulator”

for details on connecting and using the on-chip

regulator.

When the regulator is enabled, a low-ESR (< 5Ω)

capacitor is required on the VCAP/VDDCORE pin to

stabilize the voltage regulator output voltage. The

VCAP/VDDCORE pin must not be connected to VDD and

must use a capacitor of 10 µF connected to ground. The

type can be ceramic or tantalum. Suitable examples of

capacitors are shown in Table 2-1. Capacitors with

equivalent specifications can be used.

Designers may use Figure 2-3 to evaluate ESR

equivalence of candidate devices.

The placement of this capacitor should be close to

VCAP/VDDCORE. It is recommended that the trace

length not exceed 0.25 inch (6 mm). Refer to

Section 28.0

“Electrical

Characteristics”

for

additional information.

When the regulator is disabled, the VCAP/VDDCORE pin

must be tied to a voltage supply at the VDDCORE level.

Refer to Section 28.0 “Electrical Characteristics” for

information on VDD and VDDCORE.

FIGURE 2-3

FREQUENCY vs. ESR

PERFORMANCE FOR

SUGGESTED VCAP

Note:

Corrections are shown in bold. Where

possible, the original bold text formatting

has been removed for clarity.

Note:

This section applies only to PIC24FJ

devices with an on-chip voltage regulator.

0.1

0.01

0.001

0.01

0.1

100

1000 10,000

Frequency (MHz)

Note:

Typical data measurement at 25°C, 0V DC bias.

TABLE 2-1

SUITABLE CAPACITOR EQUIVALENTS

Make

Part #

Nominal

Capacitance

Base Tolerance Rated Voltage Temp. Range

TDK

C3216X7R1C106K

10 µF

±10%

16V

-55 to 125ºC

TDK

C3216X5R1C106K

10 µF

±10%

16V

-55 to 85ºC

Panasonic

ECJ-3YX1C106K

10 µF

±10%

16V

-55 to 125ºC

Panasonic

ECJ-4YB1C106K

10 µF

±10%

16V

-55 to 85ºC

Murata

GRM32DR71C106KA01L

10 µF

±10%

16V

-55 to 125ºC

Murata

GRM31CR61C106KC31L

10 µF

±10%

16V

-55 to 85ºC

PIC24FJ64GA108 bảng dữ liệu(PDF) 12 Page - Microchip Technology

PIC24FJ64GA108 bảng dữ liệu(HTML) 12 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

bảng dữ liệu tải về

Link URL