| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
WM8352 bảng dữ liệu(PDF) 38 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8352 bảng dữ liệu(HTML) 38 Page - Wolfson Microelectronics plc |
|
38 / 336 page ![]() WM8352 Production Data w PD, February 2011, Rev 4.4 38 11 CONTROL INTERFACE 11.1 GENERAL DESCRIPTION The WM8352 is controlled by writing to its control registers. Readback is available for most registers. Most aspects of the WM8352 operation can be controlled via this interface. The control interface can operate as either a 2-, 3- or 4-wire control interface: 2-wire mode uses pins SCLK and SDATA. 3-wire mode uses pins CSB, SCLK and SDATA. 4-wire mode uses pins CSB, SCLK, SDATA and SDOUT. GPIO7 is automatically enabled as CSB in 3-wire and 4-wire control modes. GPIO6 is automatically enabled as SDOUT in 4-wire control mode. Register readback is provided on the bi-directional pin SDATA in 2-/3-wire modes and on SDOUT (GPIO6) in 4-wire mode. In 2-wire mode, the control interface supports single register access as well as multiple access with or without address auto-increment. In Development Mode (see Section 14.4), the WM8352 initially selects the secondary 2-wire control interface, using pins GPIO10 and GPIO11. This enables configuration of the WM8352 via a separate interface prior to selecting the normal system operation. Note that, in Custom modes, the secondary interface is not supported. 11.2 CONTROL INTERFACE MODES The WM8352 control interface can be configured for 2-, 3- or 4-wire operation using the following register bits: ADDRESS BIT LABEL DEFAULT DESCRIPTION R6 (06h) Interface Control 3 SPI_CFG 0 Controls the SDOUT (GPIO6) pin operation in 4 wire mode 0 = SDOUT output is CMOS 1 = SDOUT output is open drain Note: SPI_4WIRE must be set for this to take effect. 2 SPI_4WIRE 0 Selects 3-wire or 4-wire SPI mode 0 = 3 wire mode using bi-directional SDATA pin 1 = 4 wire mode using SDOUT (GPIO6) Note: SPI_3WIRE must be set for this to take effect. 1 SPI_3WIRE 0 Selects 2- or 3-/4-wire mode. 0 = 2-wire mode 1 = 3-/4-wire mode Table 1 Control Interface Modes |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |