| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
WM8325 bảng dữ liệu(PDF) 34 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8325 bảng dữ liệu(HTML) 34 Page - Wolfson Microelectronics plc |
|
34 / 254 page ![]() WM8325 Production Data w PD, February 2012, Rev 4.0 34 The WM8325 monitors the DC-DC Converters and LDOs during the ON sequence to ensure that the required circuits have powered up successfully before proceeding to the next timeslot. The nominal timeslot durations are extended if necessary in order to wait for the selected DC-DC Converters or LDOs to power up. If the ON sequence has not completed within 2 seconds of starting the transition, then a Power Sequence Failure has occurred, resulting in the OFF state being forced. The most recent ON or WAKE event can be determined by reading the bits in the “ON Source” register, R400Eh. The most recent OFF event can be determined by reading the bits in the “OFF Source” register, R400Fh. The “ON Source” register is updated when a new ON event occurs. The “OFF Source” register is updated when a new OFF event occurs. Note that some Reset conditions (see Section 24) result in an OFF transition followed by an ON transition; these events are recorded as Reset events in the “ON Source” register. The ON Source and OFF Source register fields are defined in Table 2. ADDRESS BIT LABEL DEFAULT DESCRIPTION R16387 (4003h) Power State 15 CHIP_ON 0 Indicates whether the system is ON or OFF. 0 = OFF 1 = ON (or SLEEP) OFF can be commanded by writing CHIP_ON = 0. Note that writing CHIP_ON = 1 is not a valid ‘ON’ event, and will not trigger an ON transition. 14 CHIP_SLP 0 Indicates whether the system is in the SLEEP state. 0 = Not in SLEEP 1 = SLEEP WAKE can be commanded by writing CHIP_SLP = 0. SLEEP can be commanded by writing CHIP_SLP = 1. 11:10 PWRSTATE_DLY 10 Power State transition delay 00 = No delay 01 = No delay 10 = 1ms 11 = 10ms R16398 (400Eh) ON Source 15 ON_TRANS 0 Most recent ON/WAKE event type 0 = WAKE transition 1 = ON transition 11 ON_GPIO 0 Most recent ON/WAKE event type 0 = Not caused by GPIO input 1 = Caused by GPIO input 10 ON_SYSLO 0 Most recent WAKE event type 0 = Not caused by PVDD 1 = Caused by SYSLO threshold. Note that the SYSLO threshold cannot trigger an ON event. 7 ON_WDOG_TO 0 Most recent WAKE event type 0 = Not caused by Watchdog timer 1 = Caused by Watchdog timer 6 ON_SW_REQ 0 Most recent WAKE event type 0 = Not caused by software WAKE 1 = Caused by software WAKE command (CHIP_SLP = 0) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |