MCP3901 datasheet(4/62 Pages) MICROCHIP

4 / 62 page

MCP3901

DS22192D-page 4

Output Data Rate

See Table 4-2

ksps

fD = DRCLK = DMCLK/

OSR = MCLK/

(4 x PRESCALE x OSR)

Analog Input Absolute Voltage

on CH0+, CH0-, CH1+,

CH1- Pins

CHn+

-1

—

All analog input

channels, measured to

AGND (Note 7)

Analog Input Leakage Current

AIN

—1

—

(Note 4)

—2

—

-40°C < TA < 125°C

Differential Input Voltage Range (CHn+ – CHn-)

—

500/GAIN

(Note 1)

Offset Error (Note 2)

VOS

-3

—

(Note 6)

Offset Error Drift

—

µV/°C

From -40°C to +125°C

Gain Error (Note 2)

—

-0.4

—

G = 1

-2.5

—

+2.5

All Gains

Gain Error Drift

—

ppm/°C

From -40°C to +125°C

Integral Nonlinearity (Note 2)

INL

—

ppm

GAIN = 1,

DITHER = On

Input Impedance

ZIN

350

—

Proportional to

1/AMCLK

Signal-to-Noise and Distortion

Ratio (Notes 2, 3)

SINAD

—

OSR = 256,

DITHER = On

—

Total Harmonic Distortion

(Notes 2, 3)

THD

—

-104

-102

OSR = 256,

DITHER = On

—-85

-84

Signal-to-Noise Ratio

(Notes 2, 3)

SNR

—

OSR = 256,

DITHER = On

—

Spurious Free Dynamic Range

(Note 2)

SFDR

—

109

—

OSR = 256,

DITHER = On

—87

—

Crosstalk (50/60 Hz) (Note 2)

CTALK

—

-133

—

OSR = 256,

DITHER = On

ELECTRICAL CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise indicated, AVDD = 4.5 to 5.5V, DVDD = 2.7 to 5.5V; -40°C < TA < +85°C,

MCLK = 4 MHz; PRESCALE = 1; OSR = 64; GAIN = 1; Dithering OFF; VIN = -0.5 dBFS = 333 mVRMS @ 50/60 Hz

Parameters

Symbol

Min

Typical

Max

Units

Conditions

Note 1:

This specification implies that the ADC output is valid over this entire differential range and that there is no

distortion or instability across this input range. Dynamic performance is specified at -0.5 dB below the

maximum signal range, VIN = -0.5 dBFS @ 50/60 Hz = 353 mVRMS, VREF = 2.4V.

See terminology section for definition.

This parameter is established by characterization and not 100% tested.

For these operating currents, the following bit settings apply: SHUTDOWN<1:0> = 00, RESET<1:0> = 00,

VREFEXT = 0, CLKEXT = 0.

For these operating currents, the following Configuration bit settings apply: SHUTDOWN<1:0> = 11,

VREFEXT = 1, CLKEXT = 1.

Applies to all gains. Offset error is dependant on PGA gain setting (see Figure 2-19 for typical values).

Outside of this range, the ADC accuracy is not specified. An extended input range of ±6V can be applied

continuously to the part with no risk for damage.

For proper operation and to keep ADC accuracy, AMCLK should always be in the range of 1 to 5 MHz with

BOOST bits off. With BOOST bits on, AMCLK should be in the range of 1 to 8.192 MHz,

AMCLK = MCLK/PRESCALE. When using a crystal, the CLKEXT bit should be equal to ‘0’.

MCP3901 bảng dữ liệu(PDF) 4 Page - Microchip Technology

MCP3901 bảng dữ liệu(HTML) 4 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

bảng dữ liệu tải về

Link URL