33910 datasheet(53/90 Pages) FREESCALE

53 / 90 page

Analog Integrated Circuit Device Data

Freescale Semiconductor

33910

ELECTRICAL CHARACTERISTICS

STATIC ELECTRICAL CHARACTERISTICS

MC33910BAC / MC34910BAC

STATIC ELECTRICAL CHARACTERISTICS

Table 33. Static Electrical Characteristics

Characteristics noted under conditions 5.5 V

≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the

34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal

conditions, unless otherwise noted.

Characteristic

Symbol

Min

Typ

Max

Unit

SUPPLY VOLTAGE RANGE (VS1, VS2)

Nominal Operating Voltage

VSUP

5.5

–

Functional Operating Voltage(84)

VSUPOP

–

Load Dump

VSUPLD

–

SUPPLY CURRENT RANGE (VSUP = 13.5 V)

Normal Mode (IOUT at VDD = 10 mA), LIN Recessive State

(85)

IRUN

–

4.5

Stop Mode, VDD ON with IOUT = 100 µA, LIN Recessive State(85), (86), (87)

5.5 V < VSUP < 12 V

VSUP = 13.5 V

ISTOP

–

µA

Sleep Mode, VDD OFF, LIN Recessive State(85), (87)

5.5 V < VSUP < 12 V

12 V

≤ VSUP < 13.5 V

ISLEEP

–

µA

Cyclic Sense Supply Current Adder(88)

ICYCLIC

–

µA

SUPPLY UNDER/OVER-VOLTAGE DETECTIONS

Power-On Reset (BATFAIL)(89)

Threshold (measured on VS1)(88)

Hysteresis (measured on VS1)(88)

VBATFAIL

VBATFAIL_HYS

1.5

–

3.0

0.9

3.9

–

VSUP under-voltage detection (VSUV Flag) (Normal and Normal Request

modes, Interrupt Generated)

Threshold (measured on VS1)

Hysteresis (measured on VS1)

VSUV

VSUV_HYS

5.55

–

6.0

1.0

6.6

–

VSUP over-voltage detection (VSOV Flag) (Normal and Normal Request

modes, Interrupt Generated)

Threshold (measured on VS1)

Hysteresis (measured on VS1)

VSOV

VSOV_HYS

–

19.25

1.0

20.5

–

Notes

84.

Device is fully functional. All features are operating.

85.

Total current (IVS1 + IVS2) measured at GND pins excluding all loads, Cyclic Sense disabled.

86.

Total IDD current (including loads) below 100 µA.

87.

Stop and Sleep mode currents will increase if VSUP exceeds 13.5 V.

88.

This parameter is guaranteed by process monitoring but, not production tested.

89.

The flag is set during power up sequence. To clear the flag, a SPI read must be performed.

33910 bảng dữ liệu(PDF) 53 Page - Freescale Semiconductor, Inc

33910 bảng dữ liệu(HTML) 53 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

bảng dữ liệu tải về

Link URL