| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PCA9633DP2 bảng dữ liệu(PDF) 18 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCA9633DP2 bảng dữ liệu(HTML) 18 Page - NXP Semiconductors |
|
18 / 43 page ![]() PCA9633_5 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 05 — 25 July 2008 18 of 43 NXP Semiconductors PCA9633 4-bit Fm+ I2C-bus LED driver 7.7 Using the PCA9633 with and without external drivers The PCA9633 LED output drivers are 5.5 V only tolerant and can sink up to 25 mA at 5 V. If the device needs to drive LEDs to a higher voltage and/or higher current, use of an external driver is required. • INVRT bit (MODE2 register) can be used to keep the LED PWM control firmware the same (PWMx and GRPPWM values directly calculated from their respective formulas and the LED output state determined by LEDOUT register value) independently of the type of external driver. This bit allows LED output polarity inversion/non-inversion only when OE=0. • OUTDRV bit (MODE2 register) allows minimizing the amount of external components required to control the external driver (N-type or P-type device). [1] OE applies to 16-pin version only. When OE = 1, LED output state is controlled only by OUTNE[1:0] bits (MODE2 register). [2] Correct configuration when LEDs directly connected to the LEDn outputs (connection to VDD through current limiting resistor). [3] Optimum configuration when external N-type (NPN, NMOS) driver used. [4] Optimum configuration when external P-type (PNP, PMOS) driver used. Table 17. Use of INVRT and OUTDRV based on connection to the LEDn outputs when OE=0[1] INVRT OUTDRV Direct connection to LEDn External N-type driver External P-type driver Firmware External pull-up resistor Firmware External pull-up resistor Firmware External pull-up resistor 0 0 formulas and LED output state values apply[2] LED current limiting R[2] formulas and LED output state values inverted required formulas and LED output state values apply required 0 1 formulas and LED output state values apply[2] LED current limiting R[2] formulas and LED output state values inverted not required formulas and LED output state values apply[4] not required[4] 1 0 formulas and LED output state values inverted LED current limiting R formulas and LED output state values apply required formulas and LED output state values inverted required 1 1 formulas and LED output state values inverted LED current limiting R formulas and LED output state values apply[3] not required[3] formulas and LED output state values inverted not required |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |